Omron V430-F-series User Manual Download Page 164

Page: 164 / 404

Auto Focus Multi Code Reader V430-series User’s Manual (Z392)

6-39

Symbologies

Composite

When set to

Enabled

Required

, will decode the 2D composite component of a linear

symbol. The linear symbol can be DataBar-14, DataBar Expanded, DataBar Limited,

EAN-128, UPC-A, EAN-13, EAN-8, and UPC-E.

Enabled

Composite

is set to

Enabled

, the reader will decode both the 2D composite and linear

components. However, if the 2D composite component is not decoded, the linear data will

be sent by itself at the end of the read cycle.

Required

If set to

Required

, the reader must decode both components, or a No-Read will occur.

Separator Status (Composite)

Separator Character (Composite)

Note:

The Separator Character will be the same as the character defined in the

Multisymbol

Separator

field of the

<K222>

command.

Usage:

Allows reading by both linear and 2D readers.

Definition:

Combines 2D and linear width-modulated symbology on the same symbol

where different messages can be read by each reader type.

Serial Cmd:

K453,

mode,

separator status,separator

Default:

Disabled

Options:

0 = Disabled

1 = Enabled

2 = Required

Usage:

Allows the user to distinguish between the main and

Supplemental

symbols.

Definition:

Separates the linear and the composite component.

Serial Cmd:

K453,

mode,

separator status

,separator

Default:

Disabled

Options:

0 = Disabled

1 = Enabled

Usage:

As required by the application.

Definition:

Allows the user to change the separator character from a comma to a new

character.

Serial Cmd:

K453,

mode,separator status,

separator

Default:

(comma)

Options:

Any ASCII character.

Summary of Contents for V430-F-series





















































































































































































































































































































































































































Search results

Summary of Contents for V430-F-series

Reviews:

Omron V430-F-series, User Manual, Page: 164 / 404

Search results

Summary of Contents for V430-F-series

Reviews: