Omron SYSMAC NY Series Hardware User Manual Download Page 98

Page: 98 / 260

4-2-4

Ethernet Connector Specifications

Details of the RJ45 Ethernet connectors are provided below.
The Ethernet connector locks automatically to prevent unintentional disconnection.

The set of 3 RJ45 Ethernet connectors is available on all models, the single connector is optional.

Ethernet Connector Specification Details

Details of the RJ45 Ethernet connectors are provided below.

Item

Specifications

Number of available ports

3
1 extra port is optional

Physical layer

10BASE-T, 100BASE-TX or 1000BASE-T

Frame length

1,514 bytes max.

Media access method

CSMA/CD

Modulation

Baseband

Topology

Star

Transmission media

STP (shielded, twisted pair) cable of Ethernet category
5,5e or higher

Maximum transmission distance between Ethernet
switch and node

100 m

Maximum number of cascade connections

There are no restrictions if an Ethernet switch is used

4 Specifications

4-24

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands

Omron SYSMAC NY Series, Hardware User Manual

Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands