manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 42

2-1

Configuration for NYB and NYP

The Industrial PC supports the following hardware configurations.

NYB and NYP-series IPC

Ethernet

SD Memory

Card

HDD / SSD

RS-232C

DVI

Ports

NYML

Operating System

&

Software Utilities

&

APIs

or

USB

or

I/O

or

Ethernet

PCIe Card

DVI

base layer

expansion

layer

CFast Card

The major parts for configurations are layers.
• All configurations have the base layer and a cooling layer.

The base layer contains the CPU, the software and most of the connectors and functionality.

• The optional expansion layer supports PCIe cards and storage devices.
• A display layer is always present for an Industrial Panel PC.

Additional Information

• Refer to 

3-1 Layers and Components

 on page 3-3 for details.

• Refer to 

NY-series Operating Systems and Software Utilities Manual (Cat. No. W616)

 for de-

tails on the operating system, the support software and the APIs.

2 System Configurations

2-2

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands