manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 123

5-2-2

Install the PCIe Card

Prepare the following items:
• The PCIe Card.

A PCIe Card is not supplied with the Box PC.

Additional Information

• Depending on the product configuration a PCIe card can be pre-installed.

Refer to 

1-4 Product Configuration Box PC

 on page 1-5 for details.

• Refer to 

4-1-8 PCIe Card Specifications

 on page 4-14 for PCIe specifications.

• The PCIe Card mounting material: Card Support.

This item is supplied with the Box PC.

To install the PCIe Card:

1

Ensure the Box PC is OFF.

2

Remove the two crosshead screws 

1

 indicated with "open" and then pull up 

2

 the PCIe

Drawer.
The indent at the side of the drawer will help you to pull the drawer from the Box PC.

2

1

1

5 Installation

5-9

NY-series Industrial Box PC Hardware User's Manual (W553)

5-2 Install Options

5

5-2-2

 Install the PCIe Card

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands