manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 100

4-2-5

DVI Connector Specifications

DVI is the standard video interface for the Box PC.

Additional Information

• Refer to 

4-1-5 CPU Specifications

 on page 4-6 for graphics controller details.

• Refer to 

5-4-2 Ground

 on page 5-26 for grounding details.

• Refer to 

A-2 DVI Connector Pin Details

 on page A-52 for pin details.

The DVI Card specifications depend on the CPU and thus on the product configuration.

Item

Specifications

Video interface NY

£

1C

Digital only

Video interface NY

£

1E

Digital or Analog

Video interface NY

£

17

Digital or Analog

Video interface NY

£

2A

Digital only

Video interface NY

£

2C

Digital only

Video interface NY

£

25

Digital only

Video interface NY

£

35

Digital only

Resolution

Up to 1920 x 1200 pixels at 60 Hz

Type

Dual link

Maximum DVI cable length

Dependent upon connected monitor type and resolu-
tion

4 Specifications

4-26

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands