![background image](http://html1.mh-extra.com/html/omron/sysmac-cj1w-scu21-v1/sysmac-cj1w-scu21-v1_operation-manual_743586220.webp)
191
Enhanced Protocol Macro Functions
Section 5-6
5-6-1
Data Exchange Timing for Link Words
Link word specification (a method of specifying the common area for data
exchanged between the CPU Unit and the Board/Unit) is used as a method
for specifying the storage location of send/receive data when executing com-
munications sequences in protocol macro mode.
Pre-Ver. 1.2 Units
The link word area is refreshed between the CPU Unit and Board/Unit during
every CPU Unit cycle. The actual refresh timing with the CPU Unit, however,
does not correspond to whenever the I/O is refreshed. I/O refresh is per-
formed when a request is received from the Board/Unit (according to the
send/receive command executed in the communications sequence, and
therefore not synchronized with the CPU Unit scantime). This is called on-
request I/O refreshing.
Therefore, when a send command is executed ((1) in the above diagram), the
read processing of data using variables from the I/O memory addresses in the
CPU Unit specified in the link words is performed at the start of I/O refreshing
(2). The send message is compiled based on this data (3), after which the
actual message is sent (4). As a result, the actual message send timing is not
when the send command is executed, but waits until the next I/O refresh with
the CPU Unit.
Unit Ver. 1.2 or Later
The refresh between the CPU Unit and Board/Unit is the same as in earlier
models as far as being the CPU Unit’s refresh timing. I/O refresh with the CPU
Unit, however, is continuous during execution of the PMCR(260) instruction,
regardless of any request from the Board/Unit. When the send/receive com-
mand is executed, the data from within the Board/Unit is accessed and
exchanged. This method is called continuous I/O refresh and is set in the
Setup Area allocated in the DM Area.
CPU Unit
Ladder program
I/O memory
Receive data
Send data
Board/Unit
Step 0
Step 1 (send)
(2)
(1)
Ex
ecution
IN
OUT
Receive data
Send data
I1
O1
Read and compile message
(4) Send
R (O1, 2)
Link word 1
PMCR
Communications
sequence
Earlier models refresh I/O when a request is
received (using send/receive commands in the
communications sequence).
(1) to (4) are performed in
order for the processing within
this dotted line.
Send message according
to send command
Summary of Contents for SYSMAC CJ1W-SCU21-V1
