background image

P A C K A G E   C O N T E N T S

4  

6    

 H-T40

M

-P Manual Rev.A 

3.5. D

URING

 U

SE

• Emergency stop and other safety functions may not be controlled from the

status display touchscreen.

• Do not use too much force or sharp objects when touching the keys, display, 

etc.

3.6. S

ERVICE

 

AND

 M

AINTENANCE

Only qualified personnel should carry out repairs.

• The agreed warranty applies.

• Before carrying out any cleaning or maintenance operations, disconnect the

equipment from the electrical supply.

• Clean the display and surrounding front cover with a soft cloth and mild

detergent.

• Replacing the battery incorrectly may result in explosion. Only use batteries 

recommend by supplier.

3.7. D

ISMANTLING

 

AND

 S

CRAPPING

• The status display touchscreen or parts thereof shall be recycled according

to local regulations.

• The following components contain substances that might be hazardous to

health and the environment: lithium battery, electrolytic capacitor and
display.

 4 P

ACKAGE

 C

ONTENTS

4

The following parts are found in the box:

• (1) Status Display Touchscreen H-T40

M

-P

• (4) Installation fasteners

• (1) Power connector (connected to 24VDC power input)
• (1) Communication cable from HMI status display touchscreen to G9SP

Summary of Contents for Sti H-T40M-P






















Reviews: