manualshive.com logo in svg

Omron SCARA YRCX Series, Programming Manual, Page: 144 / 506

Share
Download
Omron SCARA YRCX Series Programming Manual Download Page 144

8

8-52     Chapter 8  Robot Language Lists

A

B

C

D

E

F

G

H

I

J

K

L

M

 

30

 DRIVEI

Moves the specified robot axes in a relative manner

Format

DRIVEI  [robot number]  (axis number, expression),
(axis number, expression)..., option, option

 Values 

 

robot number

 .........................1 to 4 (If not input, robot 1 is specified.)

  

axis number

 ...........................1 to 6

  

expression

 ..............................Target position (mm, deg, pulses) or point expression

 Explanation 

  Executes relative movement, including the auxiliary axes.

   

• Movement type :   PTP movement of a specified axis

   

• Point data setting :  Direct coordinate data input, point definition

   

• Options : 

Speed setting, STOPON conditions setting 

• When DRIVEI motion to the original target position is interrupted and then restarted, the target 

position for the resumed movement can be selected as the "MOVEI/DRIVEI start position" in the 
controller's parameters. (For details, refer to the YRCX user's/ operator's manual.)

  1) KEEP (default setting)   Continues the previous (before interruption) movement. The original 

target position remains unchanged.

  2) RESET 

 Relative movement begins anew from the current position. The target 
position before interruption is reset. 

Movement type 

 

●

PTP (point-to-point) of specified axis

PTP movement begins after positioning of all axes specified at <

axis number

> is complete (within 

the tolerance range), and the command terminates when the specified axes enter the OUT 
position range. When two or more axes are specified, they will reach their target positions 
simultaneously.
If the next command following the DRIVEI command is an executable command such as a 
signal output command, that next command will start when the movement axis enters the OUT 
position range. In other words, that next command starts before the axis arrives within the 
target position tolerance range.
Example:

Signal output (DO, etc.)

Signal is output when axis enters within OUT position range.

DELAY

DELAY command is executed and standby starts, when axis enters the 

OUT position range.

HALT

Program stops and is reset when axis enters the OUT position range. 

Therefore, axis movement also stops.

HALTALL

All programs in execution stop when axis enters the OUT position range, 

task 1 is reset, and other tasks terminate. Therefore, the movement also 

stops.

 HOLD

Program temporarily stops when axis enters the OUT position range. 

Therefore, axis movement also stops.

HOLDALL

All programs in execution temporarily stop when axis enters the OUT 

position range. Therefore, the movement also stops.

WAIT

WAIT command is executed when axis enters the OUT position range.

MEMO

Summary of Contents for SCARA YRCX Series



























































































































































































































































































































































































































































































































Reviews:

No comments