manualshive.com logo in svg

Omron NYP17-*-11 SERIES, User Manual

Share
Download
Omron NYP17-*-11 SERIES User Manual Download Page 253

A-2-4

Trusted Platform Module

The Trusted Platform Module (TPM) integrates encryption keys into the Industrial Panel PC in order to
secure hardware and software. The TPM enables the following security functions:
• Ensure the integrity of the platform: The TPM can be used in the BIOS and other software to protect

against unauthorized manipulation.

• Disk encryption: The TPM can be used with "BitLocker" drive encryption.
• Password protection and other uses of encryption: The TPM provides encryption key management.

Additional Information

Refer to the Microsoft Developer Network (MSDN) for best practice information.

Usage

To enable the TPM, see the relevant section in the BIOS Settings.
To use the TPM with "BitLocker" drive encryption, please follow the instructions in the operating sys-
tem.

Additional Information

Refer to 

A-1 BIOS

 on page A - 2 to enable TPM in the BIOS Settings.

Considerations

Risk of data loss: If you lose the password for the drive encryption, you will not be able to restore the
data. You will then lose access to the encrypted drive. Please store the password carefully and make
sure it is protected against unauthorized access.

Appendices

A - 17

NY-series Industrial Panel PC User's Manual (W555)

A-2 Customize W

indows

A

A-2-4 T

rusted Platform Module

Summary of Contents for NYP17-*-11 SERIES









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands