manualshive.com logo in svg

Omron NYP17-*-11 SERIES, User Manual

Share
Download
Omron NYP17-*-11 SERIES User Manual Download Page 210

7-2-5

Replace a Drive

Use the following procedure to replace a drive.

Prepare the new drive.

Additional Information

• Refer to 

1-4 Product Configuration

 on page 1 - 5 for the installed drive model.

• Refer to 

2-9-3 Storage Devices

 on page 2 - 20 for the available drive models.

• Refer to 

4-1-6 Storage Device Specifications

 on page 4 - 8 for drive specifications.

To replace a drive:

1

Power OFF the Panel PC.

2

Remove the drive cover.

1

3

2

(1) Push the lock lever 

1

.

(2) Tilt the cover 

2

.

(3) Remove the drive cover 

3

.

Additional Information

• Refer to 

2-4 Drive Bays

 on page 2 - 10 for the location of the drive cover.

• The Panel PC has 2 drive bays, marked with "A" and "B" at the left side of the drive cover.

Take note of the bay position for the drive that is being removed and do not place a drive in
the incorrect bay.

7 Maintenance

7 - 20

NY-series Industrial Panel PC User's Manual (W555)

Summary of Contents for NYP17-*-11 SERIES









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands