manualshive.com logo in svg

Omron GX-AD0471, User Manual, Page: 257 / 394

Share
Download
Omron GX-AD0471 User Manual Download Page 257

10 - 21

10   IO-Link Master Unit

GX-series EtherCAT Slave Unit User’s Manual

10-7

  Con

n

ect
ed D

evice

Sp
ecificat

ion
s and

 Mod

els

10

10-7 Connected Device Specifications and 

Models

Cables to Connect a GX-type IO-Link Master Unit to a Master or Slave with an 
RJ45 Connector

 

Connects two GX-type IO-Link Master Units

 

EtherCAT Cables

Name and appearance

Specifica-

tion

Num-

ber of 

cable 

con-

ductors

Avail-

able 

connec-

tors

Cable 

connec-

tion direc-

tion

Cable 

length

Model

XS5W Industrial Ethernet Con-
nectors with Reinforced-shield 
Cable (Cable with Connectors 
on Both Ends (M12 
Straight/RJ45))

M12 plug 
(D-cod-
ing, male) 
to RJ45

4

Smart-
click 
connec-
tor

Straight/str
aight

0.5 m

XS5W-T421-BMC-SS

1 m

XS5W-T421-CMC-SS

2 m

XS5W-T421-DMC-SS

3 m

XS5W-T421-EMC-SS

5 m

XS5W-T421-GMC-SS

10 m

XS5W-T421-JMC-SS

Name and appearance

Specifica-

tion

Num-

ber of 

cable 

con-

ductors

Avail-

able 

connec-

tors

Cable 

connec-

tion direc-

tion

Cable 

length

Model

XS5W Industrial Ethernet Con-
nectors with Reinforced-shield 
Cable (Cable with Connectors 
on Both Ends (M12 
Straight/M12 Straight))

M12 plug 
(D-coding, 
male) to 
M12 plug 
(D-coding, 
male)

4

Smart-
click 
connec-
tor

Straight/str
aight

0.5 m

XS5W-T421-BM2-SS

1 m

XS5W-T421-CM2-SS

2 m

XS5W-T421-DM2-SS

3 m

XS5W-T421-EM2-SS

5 m

XS5W-T421-GM2-SS

10 m

XS5W-T421-JM2-SS

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments