80
60
80
65
35
37.4
27.6
4
GT1
−
TS04P
TS
PWR
U.ERR
ANALOG UNIT
8
7
9
IN
Accuracy
(
±
0.3% of indication value or
±
1
°
C,
whichever greater)
±
1 digit
(
±
0.3% of indication value or
±
0.8
°
C,
whichever greater)
±
1 digit
(
±
0.3% of indication value or
±
0.5
°
C,
whichever greater)
±
1 digit
Input Type
R,S,K,J,T,B
Pt100,JPt100
-200.0 to 650.0
°
C
Pt100,JPt100
-200.0 to 200.0
°
C
Model
Input points
Input Type
Accuracy
＊
1
Conversion Cycle
Temperature Conversion Data
Insulation Resistance
Withstanding Voltage
TS04T(CST)
R, S, K, J, T, L, B
TS04P(CST)
Pt100, JPt100
4 points
250ms/4 points
Binary Data
20M
Ω
min. (at 250VDC, across insulated circuits)
500VAC, 1 minute, Detection Current 1 mA
Across I/O unit interface connector and DIN rail,
Across whole terminals and DIN rail
Across Internal Power Supply and each input
Across each input
Across I/O unit interface connector and whole terminals
＊
2
INSTRUCTION MANUAL
Thank you for purchasing this OMRON product.
This manual primarily describes precautions required in installing and
operating the digital controller. Before operating the product, read this
manual thoroughly to acquire sufficient knowledge of the product. Keep
this manual for future reference.
To ensure safe and correct use of this product, also read the following
manuals:
• CompoBus/D (Device net) Multiple I/O Terminal Operation Manual(Cat.
No. W348-E1-1)
The above manual can be obtained from any OMRON sales office or
dealer.
NOTICE
Items shown below are necessary for safe usage.
Please note them carefully.
(1) Never disassemble, repair or modify the product.
(2) Do not submit the product to abnormal shock. Doing so might result in
faulty operation.
(3) Do not use the product in the following places:
- Places subject to icing, condensation, dust or corrosive gas (espe-
cially sulfide gas or ammonia gas)
- Places subject to splashing liquid or oil atmosphere
- Place subject to static electricity or other forms of severe noise
(4) Fit the product to a DIN rail correctly.
(5) Separate the communication cables from power lines or high-tension
lines.
(6) Avoid connecting or disconnecting cables with the power ON. Doing so
might result in trouble or faulty operation.
(7) Keep the communication distance within specifications.
(8) Use the appointed communication cables.
(9) Locking Connector Cables
• Before turning the power ON, make sure that the connector cables
are firmly connected.
• Be sure that I/O interface connector is properly locked into place.
(10) Tightening Screws
Tighten screws to the stipulated torque to prevent faulty operation.
Torque: 0.3 to 0.5 N • m
(11) Never execute panel processing and wiring after installation to avoid
any conductive foreign substance inside the product.
Doing so may cause malfunction.
(12) Cleaning
Never use paint thinner or other solvent to clean the product. Doing so
might melt or discolor the surface. Use standard grade alcohol.
(13) Isolate Internal Power Supply that is connected to the product from I/O
Power Supply that is for load.
(14) Be sure to warm up more than 30 minutes before you use.
■
SPECIFICATIONS
●
Ratings
50mA max.
80mA max.
20.4 to 26.4VDC (24VDC -15 to +10%)
10A max., pulse width 1ms max.
3m in total, 1m max. between each unit
-10 to 55
°
C (no condensation)
25 to 85% (no condensation)
-25 to 65
°
C
Mounted in a panel
TS04P/T: 210g typ.,TS04PCST/TCST: 90g typ.
Current (I/O unit interface)
Consumption
(Internal power supply)
Internal Circuit Power Voltage
Inrush Current
Communication distance
I/O unit interface
Ambient Temperature
Ambient Humidity
Storage temperature
Installation
Weight
●
Characteristics
■
NOMENCLATURE
■
DISPLAY
LED name
TS
PWR
U.ERR
Condition
Lit
Lit
Out
Lit
Out
Lit
Out
LED Displaying Color
Green
Red
−
Green
−
Red
−
Normal Conditions
I/O unit interface error
Standby (or Not Powered)
Powered
Not Powered
Unit error (or Not Powered)
Device Operational
Description
■
DIMENSIONS (unit : mm)
Be sure to mount on a 35mm DIN rail using the DIN rail attachment hook.
Do not install the product in places to be touched by accident to avoid mal-
function caused by static electricity.
Do not block the ventilation holes on the upper side of product to allow heat
to escape.
Be sure to have enough space around the product when installing.
■
DIN Rail Attachment
■
DIP SWITCH SETTING
■
WIRING
●
Terminal Arrangement
●
Connecting Communications Unit and I/O unit
PRECAUTIONS IN USING THE PRODUCT
When the product is used under the circumstances or environment below, ensure
adherence to limitations of the ratings and functions. Also, take countermeasures
for safety precautions such as fail-safe installations.
(1) Use under circumstances or environment which are not described in the
instruction manual.
(2) Use for nuclear power control, railway, aircraft, viecle, incinerator, medical
equipment, entertainment equipment, safety device etc...
(3) Use for applications where death or serious property damage is possible and
extensive safety precautions are required.
6.0mm max.
6.0mm max.
for M3
Industrial Automation Company
Tokyo, JAPAN
OMRON Corporation
1615913-6D
GT1-TS04T/TS04TCST
GT1-TS04P/TS04PCST
TEMPERATURE INPUT UNIT
GT1
−
TS04P
TS
PWR
U.ERR
ANALOG UNIT
8
7
9
IN
Display
I/O unit interface
Connector
I/O unit interface
Connector
DIN rail attachment hook
DIP switch
(Side surface where
the cassette is
removed from the
terminal block)
Casset
(The cassette model
names are
GT1-TS04TCST and
GT1-TS04PCST)
Terminal Block
(Under the Cover)
SW1
OFF
ON
Set the unit
°
C
°
F
*default setting
SW3
Keep OFF
Model
GT1-TS04T(CST)
GT1-TS04P(CST)
Default Setting
2
0
The product can be connected to a communications unit and other I/O units with a
connecting cable.
･
Be sure to disconnect the I/O unit connecting cable after drawing out the cassette.
･
Use I/O unit interface (1) when connect to a communication unit.
･
Use I/O unit interface (2) when connect to another I/O unit interface (1),
use I/O unit interface (1) when connect to another I/O unit interface (2).
･
A terminating connector must be at I/O unit interface (2) of the end unit.
* DIP switch setting is read only when the power is turned ON
SW4
OFF
ON
Setting the Setting mode
DIP switch setting enable
Remote setting enable
*default setting
・
GT1-TS04T
SOURCE
+24V
SOURCE
+0V
Input0 NC Input1 NC Input2 NC Input3 NC
+
+
+
+
-
-
-
-
Input0 NC Input1 NC Input2 NC Input3 NC
A
B
1
2
3
4
5
6
7
8
9
SOURCE
+24V
SOURCE
+0V
Input0 Input0 Input1 Input1 Input2 Input2 Input3 Input3
A B A B A B A B
B
B
B
B
Input0 NC Input1 NC Input2 NC Input3 NC
A
B
1
2
3
4
5
6
7
8
9
・
GT1-TS04P
■
Installing and drawing out the cassette
Draw out the cassette towards you while pressing its upper side. (See diagram below.)
Do not draw out the cassette while power in ON.
Install the cassette to the right position with much care for direction. Check if the cas-
sette in installed properly by pulling it slightly.
Input Type and Condition
Input Type K,T in Lower -100
°
C
Input Type L
Input Type R,S in Lower 200
°
C
Input Type B in Lower 400
°
C
Accuracy
±
2
°
C
±
1 digit max.
±
2
°
C
±
1 digit max.
±
3
°
C
±
1 digit max.
Not defined
＊
1 Exceptions in accuracy
The meaning of the each LED is as follows.
●
GT1-TS04
1
2
3
4
↑
ON
SW
1
SW
4
O
N
0 1
2
3
4
5
6
7
8
9
DIP Switch
Rotaly DIP Switch
●
Setting of DIP Switch
SW2
OFF
ON
Set the display mode of temperature data
Normal mode
Decimal 2 Columns display mode
*default setting
●
Setting of Rotary DIP Switch
Position of
Rotary DIP
Switch
Input
Type
Range
（
°
C
）
0
1
2
3
4
5
6
7
8
9
R
S
K
K
J
J
T
L
L
B
0 to 1700
0 to 1700
-200 to 1300
0.0 to 500.0
-100 to 850
0.0 to 400.0
-200.0 to 400.0
-100 to 850
0.0 to 400.0
100 to 1800
Range
（
°
F
）
0 to 3000
0 to 3000
-300 to 2300
0.0 to 900.0
-100 to 1500
0.0 to 750.0
-300.0 to 700.0
-100 to 1500
0.0 to 750.0
300 to 3200
Input
Type
Range
（
°
C
）
PT100
JPT100
PT100
JPT100
-200.0 to 650.0
-200.0 to 650.0
-200.0 to 200.0
-200.0 to 200.0
Range
（
°
F
）
-300.0 to 1200.0
-300.0 to 1200.0
-300.0 to 380.0
-300.0 to 380.0
Setting Impossible except above
GT1-TS04T
GT1-TS04P
* DIP switch setting is read only when the power is turned ON
I/O Unit Connecting cable
(attached to I/O Unit)
Terminating connector
(attached to the
Communications Unit)
I/O Unit Connecting cable
(attached to I/O Unit)
DRT1-COM
MS
NS
TS
No.
COMMUNICATION UNIT
(
１
)
(
１
)
(
２
)
(
２
)
GT1
-
TS04P
TS
PWR
U.ERR
ANALOG UNIT
8
7
9
GT1
-
TS04T
TS
PWR
U.ERR
ANALOG UNIT
8
7
9
IN
IN
TS04P
TS04T
Communication unit
GT1
−
TS04T
TS
PWR
U.ERR
ANALOG UNIT
8
7
9
IN
TS04T
Vertical direction
Do not install the TS04T in
vertical direction as shown on
the left. If installed vertically,
the indication accuracy may
not be satisfied.
＊
2 Measurement condition
Accuracy does not include accuracy of external
components (thermocouple, compensating lead wires, etc.)
not included on this unit.
