Omron F3SG-PG Series, User Manual, Page: 419 / 473

389
F3SG-SR/PG
User’s Manual
Chapter
6
Wiring Exa
m
p
le
s
(f
or F3
SG-SR/PG)
Input/Output Circuit and Applications
E
6-2-1-6. Manual Reset Mode with Intelligent Tap
[Wiring Example (F3SG-SR and F3SG-PGA-A/-L *7)]
• When using the Intelligent Tap (F39-SGIT-IL3) with the emitter and receiver connected, the following functions are not available.
- External Test
- Operating Range Selection by wiring
- Optical Synchronization
• When a functional earth is necessary, wire an earth cable according to the example in
6-2-1-1. Auto Reset Mode with
Optical Synchronization and EDM Unused
. Also refer to 5-4-4. Functional Earth Connection for more information.
F3SG-SRA

F3SG-PGA-A/-L

F3SG-SRB

F3SG-PGA-C

*7
S1
F39-SGIT-IL3
24 V DC
IO-Link
Master *5
W iring for N P N *1
*6
24 V DC
F39-JG B-L/
XS5F-D521-DJ0-IL
F39-JG A-D
F39-JGR3K-L and
F39-JG
B-L
F39-JGR3K-D and F39-JG B-D
I N
PLC *2
I N 1 I N 2
S1: Locko u t/interlock reset s w itch
PLC: Programma b le logic controller (Used for monitoring only.
N OT related to safety system.)
Timing chart
Beam state: Un b locked
Blocked
Reset s w itch (S)
OSSD
Recei
v
er
Emitter
OSSD 1 (Black) OSSD 2 (
W
hite)
24
V
/0
V
(Bro
w
n)
0
V
/24
V
(Bl
u
e)
AUX (Red) MUTE B (Pink) MUTE A (Gray) RESET/EDM (Y
ello
w
)
Safety controller
*3 *4
*1. Reverse the polarity of the power supply when using in the NPN system. Select a PLC
and a safety controller of PNP or NPN type according to the system of your application.
*2. When connecting to the PLC, the output mode must be changed with the SD
Manager 3 according to your application. Refer to Chapter 4 Setting with SD
Manager 3 for more information on setting this function by the SD Manager 3.
*3. Refer to 6-3. Connectable Safety Control Units for more information.
*4. The safety controller and the F3SG-SR/PG must share the power supply or be
connected to the common terminal of the power supply.
*5. For connecting with the IO-Link Master unit, refer to an instruction manual of the
IO-Link Master unit you use.
*6. This is the case for a PELV circuit.
*7. To use F3SG-PGA-C, wire the receiver side of the emitter/receiver of F3SG-PGA-
C as shown in the above figure. Wiring of the emitter side is not needed.
*8. Make settings using the DIP Switch of the intelligent tap or SD Manager 3.
*9. To use F3SG-SR and F3SG-PGA-L in Short Mode, make settings using the DIP Switch of the
intelligent tap or SD Manager 3, restore to F3SG-SR/PG, and wire according to the wiring
diagram. F3SG-PGA-A/-C does not support the Operating Range Selection function.

: Indicates a switch position.
Function
Setting
DIP switch SD Manager 3
EDM *8 EDM Disabled [External device monitoring] : Disable
Interlock *8 Manual Reset [Start interlock] : Enable
[Restart interlock] : Enable
Operating Range Selection *9 Long [Operating Range Selection] : Long mode
Non-Muting system Perform wiring according to the wiring diagram.
N/A [Muting] : Disable
Test Input N/A
Wired Synchronization Connect the emitter and receiver with the Intelligent Tap.
㻟 㻻㻺
㻠 㻻㻺
㻡 㻻㻺
㻤 㻻㻺
Intelligent Tap Needed