INTRODUCTION
Thank you for purchasing the OMRON BP7000 Blood Pressure Monitor.
Your new blood pressure monitor uses the oscillometric method of blood pressure
measurement. This means the monitor detects your blood movement through your
brachial artery and converts the movements into a digital reading. An oscillometric
monitor does not need a stethoscope so the monitor is simple to use.
TABLE OF CONTENTS
INTENDED USE
IMPORTANT SAFETY INFORMATION
1. KNOW YOUR MONITOR
2. PREPARATION
3. USING THE MONITOR WITHOUT A SMART DEVICE
4. USING THE MONITOR WITH A SMART DEVICE
5. ERROR MESSAGES AND TROUBLESHOOTING
6. MAINTENANCE, STORAGE AND CLEANING
7. DISPOSAL
8. SPECIFICATIONS
9. SYMBOL DESCRIPTIONS / DEFINITIONS
10. FCC STATEMENT
11. LIMITED WARRANTY
12. GUIDANCE AND MANUFACTURER'S DECLARATION
INTENDED USE
This device is a digital monitor intended for use in measuring blood pressure and
pulse rate in adult patient population with arm circumference ranging from 9
inches to 17 inches (22 cm to 42 cm). The device detects the appearance of
irregular heartbeats during measurement and gives a warning signal with
readings.
IMPORTANT SAFETY INFORMATION
Please read the Important Safety Information in this instruction manual
before using the unit.
Please follow this instruction manual thoroughly for your safety.
Please keep for future reference. For specific information about your own blood
pressure, CONSULT YOUR PHYSICIAN.
Contraindications
• The device is contraindicated for use in ambulatory environments.
• The device is contraindicated for use on aircraft.
Warning
Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
• DO NOT adjust medication based on measurement results from this blood
pressure monitor. Take medication as prescribed by your physician. Only a
physician is qualified to diagnose and treat high blood pressure.
• DO NOT use this monitor on an injured arm or an arm under medical
treatment.
• DO NOT wear the arm cuff on your arm while on an intravenous drip or blood
transfusion.
• DO NOT apply or inflate the arm cuff around any body parts other than your
upper arm.
• DO NOT use this monitor in areas containing high frequency (HF) surgical
equipment, magnetic resonance imaging (MRI) equipment, computerized
tomography (CT) scanners or in oxygen rich environments.
• DO NOT use this monitor on infants, toddlers, children or persons who cannot
express themselves.
• Consult your physician before using this monitor if you have common
arrhythmias such as atrial or ventricular premature beats or atrial fibrillation;
arterial sclerosis; poor perfusion; diabetes; pregnancy; pre-eclampsia; or renal
disease. Note that any of these conditions in addition to patient motion,
trembling, or shivering may affect the measurement reading.
• Always consult your physician. Self-diagnosis of measurement results and
self-treatment are dangerous.
• Contains small parts that may cause a choking hazard if swallowed by children,
toddlers or infants.
• Keep the BATTERY out of the reach of children, toddlers and infants.
• This product emits radio frequencies (RF) in the 2.4 GHz band. DO NOT use
this product in locations where RF is restricted, such as on an aircraft or in
hospitals. For further information on any potential restrictions refer to
documentation on
Bluetooth
®
usage by the FCC.
Caution
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury to the user or patient or
damage to the equipment or other property.
• Stop using this monitor and consult your physician if you experience skin
irritation or discomfort.
• Consult your physician before using this monitor on an arm with an
arterio-venous (A-V) shunt.
• Consult your physician before using this monitor if you have had a mastectomy.
• Consult your physician before using the monitor if you have severe blood flow
problems or blood disorders as cuff inflation can cause bruising.
• Do not take measurements more often than necessary because bruising, due
to blood flow interference, may occur.
• Remove the arm cuff if it does not start deflating during the measurement.
• Do not use this monitor for any purpose other than measuring blood pressure.
• Do not use a mobile phone or other electrical devices that emit electromagnetic
fields near this monitor except when transferring your readings to your smart
device. This may result in incorrect operation of this monitor.
• Do not disassemble or attempt to repair the monitor or components. This may
cause an inaccurate reading.
• Do not use in a location where there is moisture or a risk of water splashing the
monitor. This may damage the monitor.
• Do not use this monitor in a moving vehicle such as in a car.
• Do not drop, or subject this monitor to strong shocks or vibrations.
• Do not use this monitor in places with high or low humidity or high or low
temperatures. See the “8. SPECIFICATIONS” section of the manual.
• Please check, by observation of the arm being used, that the monitor is not
causing any impairment of patient blood circulation.
• Do not use this monitor in high-use environments such as medical clinics or
physician offices.
• Avoid bathing, drinking alcohol or caffeine, smoking, exercising and eating for
30 minutes before taking a measurement.
• Rest for at least 5 minutes before taking the measurement.
• Remove tight-fitting or thick clothing from your arm while taking a measurement.
• Remain still and do not talk while taking a measurement.
Data Transmission
• Do not replace the battery while your reading is being transferred to your smart
device. This may result in the incorrect operation of your monitor and failure to
transfer your blood pressure data.
• Do not place integrated circuit cards, magnets, metal objects, or other devices
that emit electromagnetic fields near this monitor while your reading is being
transferred to your smart device. This may result in the incorrect operation of
your monitor and failure to transfer your blood pressure data.
Battery Handling and Usage
• Do not insert the batteries with their polarities incorrectly aligned.
• Use only 4 “AAA” alkaline batteries with this monitor. Do not use other types of
batteries. Do not use new and used batteries together.
• Remove the batteries if the monitor will not be used for a long period of time.
• If battery fluid should get in your eyes, immediately rinse with plenty of clean
water. Consult a physician immediately.
• If battery fluid should get on your skin, wash your skin immediately with plenty of
clean, lukewarm water. If irritation, injury or pain persists, consult a physician.
• Do not use batteries after their expiration date.
• Periodically check your batteries to ensure they are in good working condition.
• Only use batteries specified for this monitor. Use of unsupported batteries may
damage and/or may be hazardous to the monitor.
1. KNOW YOUR MONITOR
Contents:
Monitor, 4 “AAA” batteries, instruction manual, quick start guide
Monitor:
1.1 Display symbols
Connection symbol ( )
Appears when transferring the data or pairing with your smart device.
Connection OFF symbol ( )
Appears when Bluetooth is off.
Connection ON symbol ( )
Appears when Bluetooth is on.
Movement error symbol ( )
The movement error symbol will display when your body is moving during
measurement. If the movement symbol displays, remove the monitor and
wait for 2 to 3 minutes. After 2 to 3 minutes, remain still and take another
measurement.
SYNC symbol ( )
• When the SYNC symbol appears on the display, make sure that your
monitor has been pairing with the smart device or transfer the data.
• When the SYNC symbol appears on the display, transfer the data before
the measurements are deleted. Maximum internal memory is for 100
measurements. The oldest value will be deleted when this is reached
before transferring.
Irregular heartbeat symbol ( )
When the monitor detects an irregular rhythm
two or more times during the measurement, the
irregular heartbeat symbol will appear on the
display along with the measurement values.
An irregular heartbeat rhythm is defined as a
rhythm that is 25% less or 25% more than the
average rhythm detected while the monitor is
measuring the systolic and diastolic blood
pressure.
If the irregular heartbeat symbol displays with your measurement results,
we recommend you consult your physician. Follow the directions of your
physician.
Battery symbol (low) ( )
Appears when the batteries are low.
Battery symbol (depleted) ( )
Appears when the batteries are depleted.
Deflation symbol ( )
Flashes while arm cuff is deflating.
Heartbeat symbol ( )
Flashes while taking a measurement.
2013 ESH/ESC Guidelines for the management of arterial hypertension
Definitions of hypertension by office and home blood pressure levels
These are from statistical values for blood pressure.
1.2 Before Taking a Measurement
To help ensure an accurate reading, follow these directions:
• Stress raises blood pressure. Avoid taking measurements during
stressful times.
• Measurements should be taken in a quiet place.
• Keep a record of your blood pressure and pulse readings for your
physician. A single measurement does not provide an accurate indication
of your true blood pressure. You need to take and record several
readings over a period of time. Try to measure your blood pressure at the
same time each day for consistency.
2. PREPARATION
2.1 Battery Installation
1.
Remove the battery cover.
Insert your fingernail into the slot
of the battery cover, and push
downwards to remove the cover.
2.
Insert battery, slide over so it
is secured inside the circular
battery positioner. Then
insert the second battery.
3.
Replace the battery cover.
When the batteries have been securely placed in this monitor, the
message below will appear on the screen:
Notes:
• When the depleted battery symbol “
” appears on the display, turn the
monitor off and remove all the batteries. Replace with 4 new batteries at
the same time. Long life alkaline batteries are recommended.
• The measurement values continue to be stored in the memory even after
the batteries are replaced.
• The supplied batteries may have a shorter life than new batteries.
• Disposal of used batteries should be carried out in accordance with the
national/local regulations for the disposal of batteries.
• When the batteries are replaced, the words “Please pair this device.” or
“Pairing not completed. No data transfer.” will appear on the display.
Press the [ ] button to pair with the smart device or transfer the data
before taking a measurement.
2.2 Applying the Arm Cuff
1.
Apply the arm cuff to your left upper
arm.
The bottom edge of the arm cuff should be 1/2
inch (1 to 2 cm) above the elbow. The display
should be in clear view and easy to read,
positioned slightly on the inside of your arm.
2.
Securely close with the fabric
fastener.
Notes:
• The blood pressure can differ between
the right arm and the left arm, and the
measured blood pressure values can be
different. Omron recommends to always use the same arm for
measurement. If the values between both arms differ substantially, please
check with your physician as to which arm to use for your measurements.
• Positioning the monitor with the [START/STOP] button toward the body
makes it easier to use the monitor.
2.3 How to Sit Correctly
To take a measurement, you need to be relaxed and
comfortably seated, at a comfortable room
temperature.
• Sit in a chair with your legs uncrossed and your feet flat on
the floor.
• Sit upright with your back straight.
• Sit with your back and arm being supported.
• The arm cuff should be placed on your arm at the same
level as your heart.
3. USING THE MONITOR WITHOUT A SMART DEVICE
You can use this blood pressure monitor without pairing to a smart device.
3.1 Taking a Measurement
Notes:
• To stop the measurement, press the [START/STOP] button once to
deflate the arm cuff.
• Remain still and do not talk while taking a measurement.
• When using this blood pressure monitor without a smart device, you will
not be able to view your prior readings stored in the memory.
• Do not use the monitor with any other electrical device simultaneously.
This may result in incorrect operation of the monitor.
1.
Press the [START/STOP] button.
The arm cuff will start to inflate.
The following symbols indicate incorrect measurement
• If “Please remeasure” and any of these symbols below are displayed,
please take another measurement and try again.
2.
Remove the arm cuff.
3.
Write down your SYS/DIA and Pulse readings, along with
the date and time of your measurement on a piece of paper
to keep a record of your history.
4. USING THE MONITOR WITH A SMART DEVICE
4.1 Pairing Your Monitor with a Smart Device
The date and time on your monitor will automatically be set when you pair
it with your smart device.
1.
Make sure the
Bluetooth
®
in your smart device is turned
on.
2.
Download and install the free “OMRON connect” app on
your smart device.
* If you already have the “OMRON connect” app, and have created your
account, visit the “Manage Devices” in the “Profile” section of the
“OMRON connect” app to add this new device.
3.
Open the app on your smart device and follow the set-up
and pairing instructions.
4.
Confirm the monitor is connected successfully.
If the monitor is connected successfully to the smart device, “OK” will
appear on the display.
If “Error” appears, refer to section 5.1 for more detail.
For more information, visit OmronHealthcare.com
Notes:
• If you use any other app instead of “OMRON connect”, the date and time
may not be automatically set.
If you need to set the date and time, pair your monitor or transfer the data
by using “OMRON connect” app.
• The date/time will only be set for future measurements taken after the
measurement that was transferred. It will not be saved to the
measurement that was just transferred.
• Please be aware that OMRON will not be responsible for the loss of data
and/or information.
4.2 Taking a Measurement
Notes:
• To stop the measurement, press the [START/STOP] button once to
deflate the arm cuff.
• Remain still and do not talk while taking a measurement.
• This monitor will store 100 measurements. Stored measurements cannot
be viewed on the monitor's display. You will need to use the “OMRON
connect” app to view all measurements prior to the most recent reading
taken.
• Do not use a mobile phone or other electrical devices that emit
electromagnetic fields near this monitor except when transferring your
readings to your smart device. This may result in incorrect operation of
this monitor.
1.
Press the [START/STOP] button.
The arm cuff will start to inflate.
The following symbols indicate incorrect measurement
• If “Please remeasure” and any of these symbols below are displayed,
please take another measurement and try again.
2.
Remove the arm cuff.
3.
Transfer your readings.
Please make sure your monitor is within 16 ft. (5 m) of your smart device
and your “OMRON connect” app is active.
As soon as your measurement is complete, tap the “sync” icon in the
Omron connect app on your smart device to transfer your readings.
Transferring
your readings later
1. Open the app on your smart device and then follow the instructions.
2. Press [ ] button to transfer your readings.
• If your readings are successfully transferred to your smart device,
“OK” will flash on the display.
If “Error” appears, refer to section 5.1 for more detail.
Notes:
• When the SYNC symbol “
” appears on the display, transfer the data
immediately before the readings are deleted.
• When the Connection OFF symbol “
” appears on the display, turn on
the
Bluetooth
feature of your monitor. (Refer to section 4.3)
• Once you send your readings to the app, the data cannot be sent again
to the app or smart device.
4.
After your readings have been transferred to the “OMRON
connect” app, press the [START/STOP] button to turn the
monitor off.
Notes:
• The monitor will automatically turn off after 2 minutes.
• Wait 2-3 minutes before taking another measurement. Waiting between
measurements allows the arteries to return to the condition they were
prior to taking the measurement.
• If you use any other app instead of “OMRON connect”, the data may not
be displayed correctly after sending.
Data Transfer With Multiple Smart Devices
Once you transfer your data to a smart device, that data can no longer be
transferred again to the same smart device, nor to another smart device.
About Multiple Users
To share your blood pressure monitor with other people, please refer to the
“Help” section in the “OMRON connect” app.
4.3 Turning “OFF” Bluetooth
®
Turn off the
Bluetooth
®
in your monitor in the following areas where use
of wireless equipment is prohibited.
• On aircraft • In hospitals • While abroad
Your monitor comes with the
Bluetooth
®
already turned on.
1.
Turn your monitor power off if it is on by pressing the
[START/STOP] button on the monitor.
2.
Press and hold the [ ] button for more than 10 seconds.
Release the [ ] button when “
” appears on the
display. When the “ ” is blinking, you have now turned the
Bluetooth
®
off in your monitor.
3.
Press the [START/STOP] button to turn the monitor off.
Note: The monitor will automatically turn off after 2 minutes.
How to turn “ON” Bluetooth
®
Perform the following step when the power has been off.
Press and hold the [ ] button for more than 2 seconds and then
release the [ ] button when
“
”
appears on the display.
The
“ ”
will blink to show that the
Bluetooth
®
in your monitor has
been turned on.
4.4 Restoring Your Monitor to the Default Settings
To delete all the information stored in your monitor, follow the instructions
below. Make sure that your monitor is turned off. It will be off when the
screen is not showing numbers or symbols.
1.
While holding the [ ] button down, the Connection symbol
“ ” and “P” appear on the display, and then press the
[START/STOP] button for more than 5 seconds.
2.
When the “Clear” symbol appears on the display, release
the [ ] button and [START/STOP] button.
The “Clear” will appear on the display when your monitor settings have
reverted back to their original.
3.
Press the [START/STOP] button to turn the monitor off.
Notes:
• The monitor will automatically turn off after 2 minutes.
• Reverting to initial settings of this monitor will not delete the information
in the app.
• When using this monitor again, first delete the registration of monitor in
the app and then pair your monitor.
EVOLV
TM
Upper Arm
Blood Pressure Monitor
Model BP7000
Instruction Manual
9545343-5C
Connection symbol
Irregular heartbeat symbol
Connection OFF symbol
Battery symbol (low)
Connection ON symbol
Battery symbol (depleted)
Movement error symbol
Deflation symbol
SYNC symbol
Heartbeat symbol
(Flashes during measurement.)
Office
Home
Systolic Blood Pressure
≥140 mmHg
≥135 mmHg
Diastolic Blood Pressure
≥90 mmHg
≥85 mmHg
A
B
C
D
E
A. START/STOP button
B. Connection button
C. Display
D. Arm cuff
E. Battery compartment
F. Systolic blood pressure
G. Diastolic blood pressure
H. Pulse display
G
H
F
Display:
Irregular Heartbeat
Normal Heartbeat
Pulse
Blood pressure
Blood pressure
Short Long
Pulse
Avoid bathing, drinking alcohol or caffeine, smoking, exercising and eating
for 30 minutes before taking a measurement.
Rest for at least 5 minutes before taking the measurement.
Remove tight-fitting or thick clothing from your arm while taking a
measurement.
1/2 inch
(1 - 2 cm)
START
INFLATING
DEFLATING
COMPLETED
Example:
DO NOT adjust medication based on measurement results from this blood
pressure monitor. Take medication as prescribed by your physician. Only a
physician is qualified to diagnose and treat high blood pressure.
Always consult your physician. Self-diagnosis of measurement results and
self-treatment are dangerous.
Review the list of compatible smart devices at: OmronHealthcare.com
START
INFLATING
DEFLATING
COMPLETED
Example:
®
DO NOT adjust medication based on measurement results from this blood
pressure monitor. Take medication as prescribed by your physician. Only a
physician is qualified to diagnose and treat high blood pressure.
Always consult your physician. Self-diagnosis of measurement results and
self-treatment are dangerous.
HEM-7600T-Z_C_M01_161201.pdf
HEM-7600T-Z_C_M01_161201.fm 1 ページ ２０１６年１２月１日 木曜日 午後５時２５分
