E5CN-HT
Precautions for Safe Use
2152761-5A
Instruction Manual
OMRON CORPORATION
©All Rights Reserved
Suitability for Use
CAUTION
CHT1
EN
Safety Precautions
Key to Warning Symbols
Specifications
CAUTION
Warning Symbols
Digital Controller
Thank you for purchasing the OMRON E5CN-HT Digital
Controller. This manual describes the functions, performance,
and application methods needed for optimum use of
the product.
Please observe the following items when using the product.
• This product is designed for use by qualified personnel with
a knowledge of electrical systems.
• Before using the product, thoroughly read and understand
this manual to ensure correct use.
• Keep this manual in a safe location so that it is available for
reference whenever required.
For detailed operating instructions, refer to the
E5CN-HT/E5AN-HT/E5EN-HT
Digital Controllers User's Manual
(Cat. No. H169).
Significance of WARNINGs and CAUTIONs
Indicates a potentially hazardous situation which, if
not avoided, is likely to result in minor or moderate
injury or property damage. Read this manual
carefully before using the product.
Do not touch the terminals while power is being supplied.
Doing so may occasionally result in minor injury due to electric shock.
Do not allow pieces of metal, wire clippings, or fine metallic shavings or filings from installation to
enter the product. Doing so may occasionally result in electric shock, fire, or malfunction.
Do not use the product where subject to flammable or explosive gas. Otherwise, minor injury from
explosion may occasionally occur.
Never disassemble, modify, or repair the product or touch any of the internal parts. Minor electric
shock, fire, or malfunction may occasionally occur.
CAUTION - Risk of Fire and Electric Shock
a) This product is UL listed as Open Type Process Control Equipment. It must be mounted in an enclosure that
does not allow fire to escape externally.
b) More than one disconnect switch may be required to de-energize the equipment before servicing.
c) Signal inputs are SELV, limited energy.
d) Caution: To reduce the risk of fire or electric shock, do not interconnect the outputs of different Class 2 circuits.
If the output relays are used past their life expectancy, contact fusing or burning may occasionally occur. Always
consider the application conditions and use the output relays within their rated load and electrical life expectancy.
The life expectancy of output relays varies considerably with the output load and switching conditions.
Tighten the terminal screws to between 0.74 and 0.90 N•m. Loose screws may occasionally result in fire.
Set the parameters of the product so that they are suitable for the system being controlled. If they are not suitable,
unexpected operation may occasionally result in property damage or accidents.
A malfunction in the Digital Controller may occasionally make control operations impossible or prevent
alarm outputs, resulting in property damage. To maintain safety in the event of malfunction of the Digital
Controller, take appropriate safety measures, such as installing a monitoring device on a separate line.
OMRON shall not be responsible for conformity with any standards, codes, or regulations that
apply to the combination of the products in the customer's application or use of the product.
Take all necessary steps to determine the suitability of the product for the systems, machines,
and equipment with which it will be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE
OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN
DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY
RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT
OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Observe the following precautions to prevent failure to operate, malfunctions, or undesirable effects on
product performance and functions. Problems may occasionally occur. Do not handle the Controller in ways
that exceed product specifications.
(1) This product is designed for indoor use only. Do not use or store the product in any of the following
places.
• Places directly subject to heat radiated from heating equipment.
• Places subject to splashing liquid or oil atmosphere.
• Places subject to direct sunlight.
• Places subject to dust or corrosive gas (in particular, sulfide gas and ammonia gas).
• Places subject to intense temperature change.
• Places subject to icing and condensation.
• Places subject to vibration and large shocks.
(2) Use/store within the rated temperature and humidity ranges.
Provide forced-cooling if required.
(3) To allow heat to escape, do not block the area around the product.
Do not block the ventilation holes on the product.
(4) Be sure to wire properly with correct polarity of terminals.
(5) Use specified size (M3.5, width 7.2 mm or less) crimped terminals for wiring. To connect bare wires to
the terminal block, use copper braided or solid wires with a gage of AWG24 to AWG14 (equal to cross-
sectional area of 0.205 to 2.081 mm2). (The stripping length is 5 to 6 mm.) Up to two wires of same
size and type, or two crimped terminals can be inserted into a single terminal.
(6) Do not wire the terminals which are not used.
(7) Allow as much space as possible between the controller and devices that generate a powerful high-
frequency or surge.
Separate the high-voltage or large-current power lines from other lines, and avoid parallel or common
wiring with the power lines when you are wiring to the terminals.
(8) Use this product within the rated load and power supply.
(9) Make sure that the rated voltage is attained within two seconds of turning ON the power using a switch
or relay contact. If the voltage is applied gradually, the power may not be reset or output malfunctions
may occur.
(10) Make sure that the Digital Controller has 30 minutes or more to warm up after turning ON the power
before starting actual control operations to ensure the correct temperature display.
(11) A switch or circuit breaker should be provided close to this unit.
The switch or circuit breaker should be within easy reach of the operator, and must be marked as a
disconnecting means for this unit.
(12) Always turn OFF the power supply before pulling out the interior of the product, and never touch nor
apply shock to the terminals or electronic components. When inserting the interior of the product, do
not allow the electronic components to touch the case.
(13) Do not use paint thinner or similar chemical to clean with. Use standard grade alcohol.
(14) Design system (control panel, etc) considering the 2 second of delay that the controller’s output to be
set after power ON.
(15) The output may turn OFF when shifting to certain levels. Take this into consideration when performing
control.
(16) The number of non-volatile memory write operations is limited. Therefore, use RAM write mode when
frequently overwriting data during communications or other operations.
(17) Always use suitable tools to dismantle the product for disposal.
(18) Do not continue to use the product if the front surface peels or becomes cracked.
Power supply voltage
100 to 240 VAC, 50/60 Hz or
24 VAC, 50/60 Hz /24 VDC
Operating voltage range
85 to 110% of the rated voltage
Power consumption Approx. 8.5 VA (100 to 240 VAC)
Approx. 5.5 VA (24 VAC) /
Approx. 3.5 W (24 VDC)
Indication accuracy
Thermocouple:
(Ambient temperature: 23°C)
(±0.1 % of indication value or ±1°C,
whichever is greater) ±1 digit max.
Platinum resistance thermometer:
(±0.1 % of indication value or ±0.5°C,
whichever is greater) ±1 digit max.
Analog input: ±0.1 % FS ±1 digit max.
Event input
Output current: approx. 7 mA per contact.
Contact input
ON:1 k
Ω
max., OFF: 100 k
Ω
min.
No-contact input
ON: residual voltage 1.5 V max.,
OFF: leakage current 0.1 mA max.
Control output 1
Relay output :SPST-NO
250VAC, 3A(resistive load)
Voltage output (for driving SSR):
12 VDC, 21 mA
Current output: 4 to 20 mADC, 0 to 20 mADC
Load:
600
Ω
max.
Linear voltage output 0 to 10 VDC
Load: 1 k
Ω
min.
Electrical life of relay: 100,000 operations
(Long-life model: 1 million operations)
Control output 2
Voltage output (for driving SSR): 12 VDC, 21 mA
Control method
ON/OFF or 2-PID control
Auxiliary outputs
Relay outputs: 250 VAC, 3 A (resistive load),
Electrical life of relay:
100,000
operations
Ambient temperature
-10 to 55°C
(With no condensation or icing)
Ambient humidity
25 to 85%
Storage temperature
-25 to 65°C
(With no condensation or icing)
Altitude Max.
2,000m
Recommended fuse
T2A, 250 VAC, time-lag,
low-breaking
capacity
Weight
Approx. 150 g (main unit only)
Degree of protection
Front panel: IP66
Rear case: IP20, Terminal section: IP00
Installation environment
Installation category II, pollution
degree 2 (as per IEC61010-1)
Memory protection
Non-volatile memory
(Number of write operations: 1,000,000
at an ambient temperature of 25°C)
Transfer output
4 to 20 mA DC, Load : 600
Ω
max.
Operation indicators
.
ni
m
0
6
45
5
4
+0.6
0
6.
0
+
0
6.
0
+
0
(48 x number of units - 2.5)
+1
0
5
4
Individual mounting (mm) Side-by-side mounting (waterproof not possible) (mm)
•
Mode key
Press this key to change the
contents of the display.
Press this key for 1 s or longer
for reverse scroll.
Terminal
cover
Watertight
packing
Adapter
•
°C / °F : Temperature unit
The temperature unit is displayed
when the displayed value is a
temperature.
When this parameter is set to“°C”,
“
C
” is displayed, and when set to
“°F”, “
F
”is displayed.
:Protection indicator
Lit when Setting Change Protect is
ON (disables the Up and Down Keys).
MANU: Manual output indicator
Lit when the Auto/Manual Mode is set
to Manual Mode.
•
Level key
Use this key to change levels:
•
Press the
O
key and the
M
key
together for at least 3 seconds
to switch to protect level.
•
No.1 display
Process value or set data symbol
•
No.2 display
Set point, set data read-out value or
changed input value
•
Up and Down keys
Use the keys to change the values
displayed on the No.2 display.
Each press of
U
key increments or advances
the values displayed on the No.2 display.
Each press of
D
key decrements or returns
the values displayed on the No.2 display.
Dimensions
Names of parts on front panel
Installation
Wiring
Connections
(The applicability of the electric terminals varies with the type of machine.)
58
6
44.8
×
44.8
48.8
1.5
78
91
Dimensions (mm)
• A heater burnout alarm, heater short alarm, heater overcurrent alarm, or input alarm is output to the output to which the alarm 1 function is assigned.
• The voltage output (control output) is not electrically insulated from the internal wiring. When using a grounded thermocouple thermometer, one or the other
of the control output terminals must not be grounded. (If both terminals are grounded, measurements will be unreliable due to sneak current.)
• The last character of the lot number “R” indicates that reinforced insulation is provided between input power supply, relay outputs, and between other
terminals.
Conformance to EN/IEC Standards
This is a class A product.
In residential areas it may cause radio
interference, in which case the user may
be required to take adequate measures
to reduce interference.
Conformance to Safety Standards
Reinforced insulation is
provided between input power
supply, relay outputs, and
between other terminals.
•
•
In the pack:
*Main unit
*Watertight packing
*Adapter
*Instruction manual
*Terminal cover (Provided only for models with “-500”
suffix only)
Solderless terminal size: M3.5
Terminal cover: E53-COV17
USB-Serial Conversion Cable
(Sold Separately)(E58-CIFQ1)
* The main unit can be removed for maintenance without disconnecting the terminal wiring.
* Do not remove the terminal block. Doing so may result in failure or malfunction.
* A Setup Tool port is provided on the bottom of the product. Use this port to connect a personal computer to the
product when using the Setup Tool. E58-CIFQ1 USB-Serial Conversion Cable is required to connect the personal
computer to the product. (Do not use the product with the USB-Serial Conversion Cable left permanently connected.)
Refer to the instruction manual provided with the USB-Serial Conversion Cable for details on connection methods.
When waterproofing is required, be sure to mount the
controller separately.
Attach the waterproof packing from the terminal side and
then insert the controller to the panel. Recommended panel
thickness is 1 to 5 mm.
• Insert the controller through the hole in the panel. Push the adapter on from the rear and
fasten temporarily, removing any gap between the controller, panel and adapter. Finally,
secure two fixing screws alternately keeping the torque to between 0.29 to 0.39 N•m.
• Make sure that the surrounding temperature does not exceed the allowable operating
temperature given in the specifications especially when two or more controllers are
mounted.
+
−
A
B
B
−
+
+
−
V
trol output
C
Control outpu
1
• 100-240V AC Type
• 24V AC/DC Type (no polarity)
DO NOT
USE
+
−
mA
DO NOT
USE
DO NOT
USE
11
12
13
14
15
B(+)
A(
−
)
RS-485
DO NOT USE
+
-
11
12
13
14
15
DO NOT
USE
+
-
+
-
11
12
13
14
15
EV1
EV2
+
-
11
12
13
14
15
CT2
CT1
B(+)
A(
−
)
RS-485
11
12
13
14
15
CT2
CT1
+
-
11
12
13
14
15
EV1
EV2
+
-
11
12
13
14
15
RS-232C
SD
RD
SG
CT1
The E5
@
N-HT is set for a K thermocouple (input type of 5) by
default. If a different sensor is used, an input error (
s.err
) will
occur. Check the setting of the Input Type parameter.
Auxiliary output
(Relay outputs)
Auxiliary output 2
Auxiliary output
(Relay outputs)
250 VAC 3A
(resistive load)
Communications
(RS-485)
and
control output 2
(
)
Control output 2 and
transfer output
Event inputs and
Communications
(RS-485)
and
2 CTs
(
Control output 2
and 2 CTs
Event inputs and
control output 2
pp
Communications
(RS-232C)
and CT
transfer output
Transfer
output
Control output 2
rol output
12VDC,21 mA
A
DC,21 m
ppp
Control output 2
rol output
12VDC,21 mA
A
DC,21 m
ppp
Control output 2
ol output 2
12VDC,21 mA
DC,21 mA
ppp
(Load: 600
Ω
max.)
4-20 mADC
Control output 2
ol output 2
12VDC,21 mA
DC,21 m
ppp
(Load: 600
Ω
max.)
4-20 mADC
Transfer
output
Relay output
250VAC 3A
(resistive load)
Voltage output
(for driving SSR)
12 VDC 21 mA
Current output
0-20 mADC
Load 600
Ω
max
.
Linear voltage output
0-10 VDC
4-20 mADC
Load: 1 k
Ω
min.
Control output 1
The function that is set for the PF
Setting parameter will operate when
the
M
Key and
U
Key are pressed
at the same time for at least one
second.
• SUB1: Auxiliary output 1 indicator
Lit when the function assigned to
auxiliary output 1 is ON.
• SUB2: Auxiliary output 2 indicator
Lit when the function assigned to
auxiliary output 2 is ON.
• SUB3: Auxiliary output 3 indicator
Lit when the function assigned to
auxiliary output 3 is ON.
• HA: Heater burnout alarm/Heater short
alarm/Heater overcurrent alarm indicator
Lit when a heater burnout alarm, heater
short alarm, or heater overcurrent alarm
has occurred.
• WAIT: Lit while the program is in wait
status.
• OUT1: Control output 1 indicator
Lit when control output 1 is ON and not lit
when it's OFF.
For a current output, lit except for a 0% output.
• OUT2: Control output 2 indicator
Lit when control output 2 is ON and not lit
when it's OFF.
• CMW: communications writing enable/ disable
indicator
Lit when communications writing is
“enabled” and is out when it is “disabled”.
• FSP: Lit during Constant-value SP Mode.
•
RST: Lit while the program is being reset.
Auxiliary output
1
Input power supply
*1: Upper and lower limits can be set for parameters 1, 4 and 5 to provide for
different types of alarm. These are indicated by the letter "L" and "H".
• The default alarm type is "2"
*2: Error shown only for "Process value / Set point". Not shown for other status.
When an error has occurred, the No.1 display shows the error code. Take
necessary measure according to the error code, referring the table bellow.
If the input value exceeds the display limit ( -19999 to 32400), though it is within the control
range,
[[[[
will be displayed under -19999 and
]]]]
above 32400. Under these conditions,
control output and alarm output will operate normally.
For information on the controllable range, refer to the
E5CN-HT/E5AN-HT/E5EN-HT Digital Controllers
User's Manual
(Cat. No. H169).
Turn the power OFF then back ON again. If the
display remains the same, the controller must be
repaired. If the display is restored to normal, then
a probable cause can be external noise affecting
the control system. Check for external noise.
After the correction of A/D converter error, turn the
power OFF then back ON again. If the display
remains the same, the controller must be repaired.
If the display is restored to normal, then a
probable cause can be external noise affecting the
control system. Check for external noise.
No.1 display
Meaning
A/D converter error
*2
Memory error
Input error
*2
s.err
(S. Err)
e111
(E111)
Action
OFF
Alarm
Control
output
Status at error
OFF
OFF
Operates
as above the
upper limit.
OFF
OFF
e333
(E333)
Input type
Error display (trouble shooting)
Operation menu
*1
*1
*1
*The default is“5”.
*
s.err
will be displayed when a platinum resistance thermometer is mistakenly connected while
input type is not set for it. To clear the
s.err
display, correct the wiring and cycle the power supply.
Alarms
−
200.0 to 850.0 (
°C)
−
199.9 to 500.0 (
°C)
0.0 to 100.0 (
°C)
−
199.9 to 500.0 (
°C)
0.0 to 100.0 (
°C)
−
200.0 to 1300.0 (
°C)
−
20.0 to 500.0 (
°C)
−
100.0 to 850.0 (
°C)
−
20.0 to 400.0 (
°C)
−
200.0 to 400.0 (
°C)
−
199.9 to 400.0 (
°C)
−
200.0 to 600.0 (
°C)
−
100.0 to 850.0 (
°C)
−
200.0 to 400.0 (
°C)
−
199.9 to 400.0 (
°C)
−
200.0 to 1300.0 (
°C)
0.0 to 1700.0 (
°C)
0.0 to 1700.0 (
°C)
100.0 to 1800.0 (
°C)
0.0 to 2300.0 (
°C)
0.0 to 1300.0 (
°C)
−
50.00 to 200.00 (
°C)
−
50.00 to 200.00 (
°C)
−
50.00 to 200.00 (
°C)
−
50.00 to 200.00 (
°C)
/
−
300.0 to 1500.0 (
°F)
/
−
199.9 to 900.0 (
°F)
/ 0.0 to 210.0 (
°F)
/
−
199.9 to 900.0 (
°F)
/ 0.0 to 210.0 (
°F)
/
−
300.0 to 2300.0 (
°F)
/ 0.0 to 900.0 (
°F)
/
−
100.0 to 1500.0 (
°F)
/ 0.0 to 750.0 (
°F)
/
−
300.0 to 700.0 (
°F)
/
−
199.9 to 700.0 (
°F)
/
−
300.0 to 1100.0 (
°F)
/
−
100.0 to 1500.0 (
°F)
/
−
300.0 to 700.0 (
°F)
/
−
199.9 to 700.0 (
°F)
/
−
300.0 to 2300.0 (
°F)
/ 0.0 to 3000.0 (
°F)
/ 0.0 to 3000.0 (
°F)
/ 300.0 to 3200.0 (
°F)
/ 0.0 to 3200.0 (
°F)
/ 0.0 to 2300.0 (
°F)
/
−
50.00 to 200.00 (
°F)
/
−
50.00 to 200.00 (
°F)
/
−
50.00 to 200.00 (
°F)
/
−
50.00 to 200.00 (
°F)
K
J
T
E
L
U
N
R
S
B
W
PLII
K
J
T
Pt100
4 to 20mA
0 to 20mA
1 to 5V
0 to 5V
0 to 10V
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
One of the following ranges is used depending on scaling.
:
−
19999 to 32400
−
1999.9 to 3240.0
−
199.99 to 324.00
−
19.999 to 32.400
Input type
Platinum
resistance
thermometer
Input
Pt100
JPt100
Thermocouple
Platinum
resistance
thermometer
Current input
Voltage input
Setting
Input setting range
Vary with "L", "H" values
Vary with "L", "H" values
Vary with "L", "H" values
X
ON
OFF
SP
X
ON
OFF
SP
ON
OFF
SP
X
X
ON
OFF
SP
L H
ON
OFF
SP
X
ON
OFF
SP
X
ON
OFF
SP
X
ON
OFF
0
ON
OFF
X
0
X
ON
OFF
0
X
ON
OFF
0
ON
OFF
X
0
X
ON
OFF
0
L H
ON
OFF
SP
L
H
ON
OFF
SP
SP
X
ON
OFF
SP
ON
OFF
X
ON
OFF
X
0
ON
OFF
X
0
1
0
2
3
4
5
6
7
8
9
10
11
12
13
Alarm output function
Positive alarm value (X) Negative alarm value (X)
Alarm type
Setting
No alarm function
Deviation upper/lower limit
standby sequence ON
Absolute value upper limit
Absolute value lower limit
Absolute value upper limit
standby sequence ON
Absolute value lower limit
standby sequence ON
LBA (only for alarm 1)
Deviation lower limit
standby sequence ON
Deviation upper limit
standby sequence ON
Deviation upper/lower range
Deviation upper limit
Deviation upper/lower limit
Deviation lower limit
Output off
PV change rate alarm
Check the setting of the Input Type parameter,
check the input wiring, and check for broken or
shorts in the temperature sensor.
: Can be displayed
and changed
: Can be displayed
× : Display or shifting to
another level is not
possible.
Default setting : 0
× : Change to other levels not possible
Protection function
Operation/Adjustment protection
Setting change protection
Setting changes by key operation are restricted.
OFF
off
: Setting can be changed by key operation
ON
on
: Setting cannot be changed by key operation (“ ” will light.)
(Protect level settings can all be changed.)
Other functions
: Change to other levels possible
*
AT in Adjustment level
Designate "
at-2
: 100% AT execute" or
"
at-1
: 40% AT execute" to execute AT and
"
off
: AT cancel" to cancel AT.
“
at
” flashes
“AT cancel”
Also when AT execution ends, the
display automatically returns to “
off
”.
at
off
at
at-2
AT (auto-tuning)
“100%AT Execute”
Hold
O
down for at least 1 second
Adjustment Level
Moving to the next level is
possible when the password
(-169) is input.
Set value
0
1
2
×
×
×
×
Initial setting
level
Communications
setting level
Advanced function
setting level
Initial setting/Communications protection
This protect level restricts movement to the initial setting level,
communications setting level and advanced function setting level.
PID Setting Level
Operation Level
Hold
O
and
M
keys down for
at least 1 second
oapt
0
icpt
0
wtpt
off
prlp
0
Protect Level
Operation / Adjustment
Protect
Initial Setting /
Communication Protect
Setting Change Protect
Password to Move
to Protect Level
Restricts which settings can be displayed
or changed, and restricts change by key
operation.
Advanced Function
Setting Level
Hold
O
down
for at least
1 second
Hold
O
down for at
least 3 seconds
Only the value set to the
ins
: temperature input shift parameter is applied to
the entire temperature input range. When the process value is 200°C, the
process value is treated as 201.2°C after input shift if the input shift value is
set to 1.2°C. The process value is treated as 198.8°C after input shift if the
input shift value is set to -1.2°C.
OMRON EUROPE B.V.
Wegalaan 67-69, NL-2132 JD Hoofddorp The Netherlands
Phone 31-2356-81-300
FAX 31-2356-81-388
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg, IL 60173-5302 U.S.A
Phone 1-847-843-7900
FAX 1-847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark, Singapore 119967
Phone 65-6835-3011
FAX 65-6835-2711
OMRON Corporation
Shiokoji Horikawa, Shimogyo-ku, Kyoto 600-8530 JAPAN
Settings shown below are the parameters displayed for the models without options.
(Options include heater burnout detection, communications, event inputs, and
control output 2.)
Check the wiring before turning ON the power supply.
The following table shows the relationship between settings and
protect limits related to Operation level and Adjustment level.
Protection function, to prevent unwanted settings,
restricts the setting items to be used or designates
if operation of the key is valid or invalid.
Input Type *3
Scaling Upper Limit
(only when setting analog input)
Scaling Lower Limit
(only when setting analog input)
Decimal Point
(only when setting analog input)
SP Upper Limit
SP Lower Limit
PID/ONOFF
In ON/OFF control =
onof
In 2-PID control =
pid
Standard or Heating/Cooling
Standard control =
stnd
Heating and cooling control =
h-c
(Select standard control or heating
and cooling control as required)
Control Period
(Heating)(Unit: Seconds)
Alarm 2 Type:
Control Period (Cooling)(Unit:
Seconds)
(C stands for Celsius,
F for Fahrenheit)
Direct/Reverse OperationIn
Reverse operation (Heating) =
or-r
In Direct operation (Cooling) =
or-d
*3: Refer to the adjoining tables for details of input
types and alarm types.
*4: Applicable only to models with alarm functions.
*5: Operation is stopped when moved to the initial
setting level.
(Control/alarm are both stopped.)
*6: The grayed-out setting items may not be
displayed according to the models and setting.
*6
*6
*6
*6
*6
*6
*6
*6
Transfer Output Type
Transfer Output Upper Limit
Transfer Output Lower Limit
Linear Current Output
Program Time Unit
Time Setting/Slope Setting
Slope Time Setting Unit
Reset Operation
Operation after Power ON
Operation at End of Operation
PV Start
*6
*6
*6
*6
Default setting : 0
Process value
PV/SP
Others
Program Setting Level
Adjustment level
PID Setting Level
Level
Set value
Oper
a
tion
le
v
e
l
Alarm 1 Hysteresis
*6
Alarm 2 Hysteresis
*6
Extraction of Square Root Enable
(Only when analog input is set)
*6
*6
*6
*6
Initial setting level enables users to specify their
preferred operating conditions
(input type, alarm type, control method, etc.)
Move to Advanced Function
Setting Level
init
off
For parameters in the Advanced Function Setting
Level, PID Setting Level, Monitor/Setting Item
Level, and Manual Control Level and for other
information, refer to the
E5CN-HT/E5AN-HT/E5EN-HT User's Manual
(Cat. No. H169).
For information on communications, refer to the
E5CN-HT/E5AN-HT/E5EN-HT Communications
Manual
(Cat. No. H170).
Temperature Input Shift
(Unit: °C or °F)
Upper Limit Temperature
Input Shift Value
when 2 point input shift
is selected
Lower Limit Temperature
Input Shift Value
when 2 point input shift
is selected
Adjustment Level
Proportional Band
Integral Time
(Unit: secs)
AT Execute / Cancel
100%AT Execute
at-2
40%AT Execute
at-1
*6
*6
*6
*6
*6
*6
l.adj
at
off
SP Mode
*6
spmd
psp
Constant SP
fsp
0.0
ins
0.0
insh
0.0
insl
0.0
p
8.0
i
233.0
Derivative Time
(Unit: secs)
*6
d
40.0
Dead Band
Manual Reset Value
(Unit: %)
Hysteresis
(Cooling)
MV Upper Limit
MV Lower Limit
Hysteresis
(Heating)
*6
*6
*6
*6
*6
*6
hys
1.0
chys
1.0
ol-h
105.0
ol-l
-5.0
c-db
0.0
of-r
50.0
Cooling Coefficient
*6
c-sc
1.00
Wait Band
*6
wt-b
off
MV Change
Rate Limit
*6
orl
0.0
Standby Time
stb
0.00
Extraction of Square
Root Low-cut Point
*6
sqrp
0.0
Adjustment level is for
entering set values and shift
values for control.
d.seg
1
d.seg
0
PID Set
No.
pid
1
Alarm
Value 1
al-1
0.0
Alarm
Upper
Limit 1
al1h
0.0
Alarm
Lower
Limit 1
al1l
0.0
Alarm
Value 2
al-2
0.0
Alarm
Upper
Limit 2
al2h
0.0
Alarm
Lower
Limit 2
al2l
0.0
Alarm
Value 3
al-3
0.0
Alarm
Upper
Limit 3
al3h
0.0
Alarm
Lower
Limit 3
al3l
0
Program
Repetitions
rpt
0
Program Link
Destination
link
end
Time Signal 1
Set Segment
ts1s
0
Time Signal 1
ON Time
on1
0.00
Time Signal 1
OFF Time
of1
0.00
Segment
n Format
styp
ramp
Segment
n SP
sp
0.0
Segment
n Slope
pr
0.0
Segment
n Time
time
0.00
Time Signal 2
Set Segment
t525
0
Time Signal 2
ON Time
on2
0.00
Time Signal 2
OFF Time
of2
0.00
Number of Segments
Used, 1 to 32
s-no
8
Display Segment Selection,
END or 0 to Number of
Segments − 1
d.seg
end
d.seg
7
d.prg
2
d.prg
1
Display Program Selection
d.prg
0
d.prg
7
In this level, the SPs and times
are input for the programs.
t-u
h-m
pru
m
rtsm
stop
p-on
cont
eset
rst
t-pr
time
pvst
sp
amov
0
in-t
5
in-h
100
in-l
0
dp
0
d-u
c
sl-h
1300.0
sl-l
-200.0
cntl
pid
s-hc
stnd
cp
20
c-cp
20
orev
or-r
alt1
2
alt2
2
tr-t
off
tr-h
100.0
tr-l
0.0
o1-t
4-20
alh1
0.2
alh2
0.2
sqr
off
Operation level should normally be
used during operations.
PV/SP
s.err
is displayed when
connected sensor is
different from input type.
Segment No. Monitor
Hold
Advance
Run/Reset
At start of program operation:
run
At end of program operation:
rst
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
Program Number
Auto/Manual Switch
Elapsed Program
Time Monitor
Program Execution
Repetition Monitor
Remaining Standby
Time Monitor
seg
0
hold
off
adv
off
r-r
rst
prg
0
25.0
0.0
a-m
prgt
0.00
rptm
0
stbm
0.00
d.pid
1
Operation stopped.
(Control/alarm are both stopped.)
*5
Initial Setting Level
Temperature Unit °
C =
c
°
F =
f
Alarm 1 Type:
*3
*4
*3
*4
POWER ON
Press
O
Key for
less than
1 s.
Hold
O
and
M
keys down for
at least 3 seconds
Program Setting Level
Parameter
Initialization
Press
O
Key for
less than 1 s.
Display PID
Selection
Press
O
Key for
less than 1 s.
Press
O
Key for less
than 1 s.
Protection can be set for the PF Key operation. The PF Key operation is
executed by pressing the
M
and
U
Keys at the same time.
PF key protection
OFF “
off
”: PF Key enabled.
ON ”
on
” : PF Key disabled.
For other information, refer to the
User's Manual
(Cat. No. H169).
For other information, refer to the
User's Manual
(Cat. No. H169).
U
D
48
×
48
