manualshive.com logo in svg

Omron CJ1G-CPUxx, Instructions Manual

Share
Download
Omron CJ1G-CPUxx Instructions Manual Download Page 205

184

Sequence Output Instructions

Section 3-4

3-4-8

SINGLE BIT OUTPUT: OUTB(534) 

Purpose

OUTB(534) outputs the status of the instruction’s execution condition to the
specified bit. OUTB(534) can control a bit in the DM Area or EM Area, unlike
OUT.

This instruction is supported by the CS1-H, CJ1-H, CJ1M, and CS1D CPU
Units only.

Ladder Symbols

Variations

Note Immediate refreshing is not supported by the CS1D CPU Units.

Applicable Program Areas

Operands

D: Word Address

Specifies the word containing the bit to be controlled.

N: Beginning Bit

Specifies the bit to be controlled. N must be #0000 to #000F (&0 to &15).

Operand Specifications

OUTB(534)

D

N

D: Word address
N: Bit number

Variations

Executed Each Cycle for ON Condition

OUTB(534)

Executed Once for Upward Differentiation

@OUTB(534)

Executed Once for Downward Differentiation Not supported

Immediate Refreshing Specification (See note.)

!OUTB(534)

Block program areas

Step program areas

Subroutines

Interrupt tasks

Not allowed

OK

OK

OK

Area

D

N

CIO Area

CIO 0000 to CIO 6143

Work Area

W000 to W511

Holding Bit Area

H000 to H511

Auxiliary Bit Area

A448 to A959

A000 to A959

Timer Area

T0000 to T4095

Counter Area

C0000 to C4095

DM Area

D00000 to D32767

EM Area without bank

E00000 to E32767

EM Area with bank

En_00000 to En_32767

(n = 0 to C)

Indirect DM/EM addresses in 
binary 

@ D00000 to @ D32767

@ E00000 to @ E32767

@ En_00000 to @ En_32767

(n = 0 to C)

Indirect DM/EM addresses in 
BCD

*D00000 to *D32767

*E00000 to *E32767

*En_00000 to *En_32767

(n = 0 to C)

Constants

---

#0000 to #000F (binary) 
or &0 to &15

Data Registers

DR0 to DR15

Summary of Contents for CJ1G-CPUxx

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands