Omicron CPC 100 Getting Started Download Page 10

CPC Getting Started

10

OMICRON

Opening the 

CPC

 or its accessories without authorization invalidates all warranty claims. Any kind of 

maintenance, calibration or repair on the device itself may only be carried out by persons authorized by 
OMICRON.

1.7

Disclaimer

If the equipment is used in a manner not described in the user documentation, the protection provided 
by the equipment may be impaired.

1.8

Compliance statement

Declaration of conformity (EU)

The equipment adheres to the guidelines of the council of the European Community for meeting the 
requirements of the member states regarding the electromagnetic compatibility (EMC) directive, the low 
voltage directive (LVD) and the RoHS directive.

FCC compliance (USA)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the user will be 
required to correct the interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the 
user's authority to operate the equipment.

Declaration of compliance (Canada)

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

1.9

Recycling

This test set (including all accessories) is not intended for household use. At 
the end of its service life, do not dispose of the test set with household waste!

For customers in EU countries (incl. European Economic Area)

OMICRON test sets are subject to the EU Waste Electrical and Electronic 
Equipment Directive 2012/19/EU (WEEE directive). As part of our legal obligations 
under this legislation, OMICRON offers to take back the test set and ensure that it is 
disposed of by authorized recycling agents.

For customers outside the European Economic Area

Please contact the authorities in charge for the relevant environmental regulations in 
your country and dispose the OMICRON test set only in accordance with your local 
legal requirements.

Summary of Contents for CPC 100























Reviews: