background image

 
 

Hardware Setup 

3.4

 

Rear Panel 

The power, fuses and outputs are located on the rear panel of the Benchtop Digital Controller. The 
optional Ethernet port is also located at the rear of the unit. 

                                   
 

 

 

   

 

 

 

 

 

                                 

 

 

Figure 7.   Rear Panel. 

(Not to scale)

 

 

Table 6.   Rear Panel Components List. 

Item 

Name 

Description 

ON/OFF Switch 

 

AC Power Fuses 

90 to 240 Vac, 50/60 Hz, Time Lag 

 

F1 (Fuse) 

Protects the AC power input 

F2 (Fuse) 

Protects Output 1 

F3 (Fuse) 

Protects Output 2 

Ethernet Port (RJ45) 

10/100Base-T (Optional) 

AC Main Input Plug 

IEC60320 C13, Power Socket. 90 to 240 Vac, 50/60 Hz 

Output 1 

Relay Output, 90-240 VAC ~ 3A Max 

Output 2 

SSR Output, 90-240 VAC ~ 5A Max 

Isolated Analog Terminal 

0-10V or 0-24mA Output (Optional) 

 

 

Single Phase AC Input Only. Neutral line is not fused or switched. 
Outputs 1 and 2 are sourced directly from the Main AC Input. 

 

3.5

 

Isolated Analog Output 

Table 7

 shows the wiring of the optional Isolated Analog Output terminals. 

 

Table 7.   Analog Output Terminals. 

Terminal 

Description 

Analog Output

 

Not Connected 

Analog Return 

 

 

 

Figure 8.   Analog Output Terminals

 

Summary of Contents for CS8DPT

















Reviews: