background image

 
 

14 

Specifications 

5

 

SPECIFICATIONS 

Table 9 

is a summary of the specifications unique to the Benchtop Digital Controller. It take precedence 

where applicable. For detailed specifications refer to the Platinum Series User’s Manual (

M5451

).

 

 

Table 9.   Benchtop Digital Controller Specifications Summary. 

Model CS8DPT/CS8EPT 

Display 

4 or 6-Digit 

Sensor Input(s) Channel 

Single-Channel, Universal Input 

Power All Models: 
Fused: 

90 to 240 VAC 50/60 Hz (Single Phase Only) 
Time-Lag, 0.1A, 250 V 

All Outputs 
Output 1:  
Output 2: 

90 to 240 VAC 50/60 Hz (Single Phase Only) 
Fast-Blow, 3A, 250 V 
Fast-Blow, 5A, 250 V 

Enclosure: 
Material: 
Size: 

Case - Plastic (ABS) 
236mm W x 108mm H x 230mm D 
(9.

3”

 W x 

4.3”

 H x 9.1

” D)

 

Weight:   

1.14 kg (2.5 lb) 

 

 

Approval Information 

 

This product conforms to the 

EMC: 2014/30/EU (EMC Directive)

 

Electrical Safety: 2014/35/EU (Low Voltage Directive)

 

Safety requirements for electrical equipment for  
measurement, control, and laboratory.  

EMC Measurement Category I 

Category I includes measurements performed 
on circuits not directly connected to the Mains 
Supply (power). Maximum Line-to-Neutral 
working voltage is 50Vac/dc. This unit should 
not be used in Measurement Categories II, III, 
and IV. 

Transients Overvoltage Surge

 

(1.2 / 50uS pulse)

 

 

Input Power: 

2000 V 

 

Input Power: 

1000 V 

 

Ethernet: 

1000 V 

 

Input/Output Signals:  500 V 

Double Insulation; Pollution Degree 2 
Dielectric withstand Test per 1 min

 

 

Power to Input/Output: 

2300 Vac  (3250 Vdc) 

 

Power to Relays/SSR Output:  2300 Vac  (3250 Vdc) 

 

Ethernet to Inputs: 

1500 Vac  (2120 Vdc) 

 

Isolated RS232 to Inputs: 

500 Vac   (720 Vdc) 

 

Isolated Analog to Inputs: 

500 Vac   (720 Vdc) 

 
ADDITIONAL INFORMATION:   
FCC: 

This device complies with Part 15, Subpart B, Class B of the FCC rules, for option 

EIP only.  

RoHS II:

 The above product has been declared by the original supplier as Compliant. The manufacturer 

of this item declares that the product complies with the EEE RoHS II Directive 2011/65/EC. 
 

UL File Number: E209855

 

 

 

 

 

Summary of Contents for CS8DPT

















Reviews: