Olympus OFP-2 Instructions Manual Download Page 38

Chapter 5 Cleaning and Sterilizing

FLUSHING PUMP OFP-2

38

Chapter 5 Cleaning and Sterilizing

WARNING

Water containers and caps are not cleaned or sterilized before 

shipment. Before using water container and caps for the first time, 

reprocess according to the instructions given in this Chapter.

5.1  Importance of cleaning, disinfection, and sterilization

The medical literature reports incidents of cross contamination resulting from improper cleaning, 

disinfection, or sterilization. It is strongly recommended that all individuals engaged in 

reprocessing closely observe all instructions given in this manual and the manuals of all ancillary 

equipment, and have a thorough understanding of the following items:

Professional health and safety criteria of your hospital

Individual cleaning, disinfection, and sterilization protocols

Structure and handling of endoscopic equipment

Handling of pertinent chemicals

For the types and conditions of the means of cleaning, disinfection, and sterilization to be adopted, 

please make judgments from your professional viewpoints.

WARNING

• Water containers and caps should be emptied, cleaned and sterilized at 

least once per day. Failure to do so could pose an infection control risk.

• Failure to properly clean and sterilize the water container and caps 

could lead to infection.

• During cleaning and sterilizing, wear appropriate personal protective 

equipment, such as eye wear, face mask, moisture-resistant clothing  

and chemical-resistant gloves that fit properly and are long enough so 

that your skin is not exposed.

• Patient debris and reprocessing chemicals are hazardous. Wear 

personal protective equipment to guard against dangerous chemicals 

and potentially infectious material. During cleaning and disinfection or 

sterilization, wear appropriate personal protective equipment, such as 

eye wear, face mask, moisture-resistant clothing, and chemical-resistant 

gloves that fit properly and are long enough so that your skin is not 

exposed. Always remove contaminated personal protective equipment 

before leaving the reprocessing area.

• The disinfection/sterilization room must be adequately ventilated. 

Adequate ventilation protects against the buildup of toxic chemical 

fumes.

• Turn off the OFP-2 and disconnect the power cord prior to cleaning and 

servicing.

CAUTION

• Do not drop the water container or subject it to impacts. The container 

could become damaged and unusable.

Summary of Contents for OFP-2

































































Reviews: