background image

This telephone is not designed for making emergency telephone calls 

when the power fails.  Make alternative arrangements for access to 

emergency services.

BEFORE USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY 

PRECAUTIONS SHOUD ALWAYS BE FOLLOWED TO REDUCE THE RISK 

OF FIRE, ELECTRIC SHOCK AND INJURY, INCLUDING THE FOLLOWING.

5

Read and understand all instructions.

5

Follow all warnings and instructions marked on the product.

5

Unplug this product from the wall outlet before cleaning.  Do not use 

liquid cleaners or aerosol cleaners.  Use a damp cloth for cleaning.

5

Do not use this product near water, for example, near a bathtub, 

washbowl, kitchen sink, or laundry tub, in a wet basement, or near a 

swimming pool.

5

Do not place this product on an unstable cart, stand, or table.  The 

product may fall, causing serious damage to the product.

5

Slots and openings in the cabinet and the back or bottom are provided 

for ventilation, to protect it from overheating, these openings must not 

be blocked or covered.  The openings should never be blocked by 

placing the product on the bed, sofa, rug, or other similar surface.

5

This product should never be placed near or over a radiator or heat 

register.  This product should not be placed in a built-in installation 

unless proper ventilation is provided.

5

This product should be operated only from the type of power source 

indicated on the marking label.  If you are not sure of the type of power 

supply to your place, consult your dealer or local power company.

5

Do not allow anything to rest on the power cord.  Do not locate this 

product where the cord will be abused by persons walking on it.

5

Do not overload wall outlets and extension cords as this can result in 

the risk of fire or electric shock.

5

Never push objects of any kind into this product through cabinet slots 

as they may touch dangerous voltage points or short out parts that 

could result in a risk of fire or electric shock.  Never spill liquid of any 

kind on the product.

5

To reduce the risk of electric shock, do not disassemble this product.  

Take the product to a qualified serviceman when it requires repair work 

or service.  Opening or removing covers may expose you to dangerous 

voltages or other risks.  Incorrect reassembly can cause electric shock 

during subsequent use.

5

Unplug this product from the wall outlet and battery source and refer 

servicing to qualified service personnel under the following conditions:

a. When the power supply cord or plug is damaged or frayed.

b. If liquid has been spilled into the product.

c. If the product does not operate normally by following the operating 

instructions.  

d. If the product has been dropped or the cabinet has been damaged.

e. If the product exhibits a distinct change in performance.

5

Avoid using a telephone during an electrical storm.  There may be a 

remote risk of electric shock from lightning.

5

Do not use this product to report a gas leak in the vicinity of the leak.

1

2

Summary of Contents for OL6010





















Reviews: