background image

Congratulations 

on your purchase of the  

Olympia AD220 Cree

®

 XP-G LED 

high-

performance flashlight. This product is designed 

to provide you with the best possible functionality.  

The AD220 utilizes Cree

®

 LED technology that 

is geared for optimum brightness and efficiency. 

It’s constructed in aircraft-grade aluminum with 

premium Type II hard anodized, anti-abrasive 

finish. The lightweight, compact design makes 

it a functional light for multiple uses including 

hunting, hiking, camping, caving, general 

household use, recreational activities, rugged 

sports or emergency situations. Please take a 

few moments to read this user guide to ensure 

that you get the best performance and years of 

trouble-free service.

Product Description

Battery Installation

1.  Unscrew the tail switch cap and insert 

2xCR123 (non-rechargeable / 1x16340 

(rechargeable) *batteries. The (+) terminal on 

the batteries should face toward the flashlight’s 

head. 

2. Replace the tail switch cap and be sure to 

tighten snugly, but do not over tighten as this 

could strip the threads in the cap.  Turn on the 

flashlight as indicated in any of the options 

listed in the table that follows. 

Note: If the tail 

cap is not tightened snugly; the flashlight 
will not turn on.

3. When the battery life is nearly depleted, your 

flashlight will blink to indicate new batteries are 

needed.

*Non-rechargeable batteries included

Flashlight Operation

Your 

Olympia AD220 Cree

®

 XP-G LED

 high-

performance flashlight has a push-button tail 

switch for on/off operation and is equipped with 

1) Momentary and 2) Continuous light options. 

It also has 5 light modes to suit your varied 

needs. See table instructions to access these 

functionalities:

Olympia AD220  
Cree

®

 XP-G LED  

Flashlight

User Guide

Lighting Operation Modes

Momentary-on 

Lighting

Press the push-button tail switch 

half-way to activate the light 

momentarily.

Continuous 

Lighting 

Press the tail switch push-button to 

completely turn on the flashlight. 

The light will stay on until the push-

button is turned off.

Lighting Modes

There are five types of light output:

High

Middle

 

Low

Strobe

SOS

Press the tail push-button to switch 

to each mode

Accessing the 5 Lighting Modes

High Beam

Press the push-button tail  

switch once

Mid Beam

Press the push-button tail  

switch twice

Low Beam

Press the push-button tail  

switch 3 times

Strobe

Press the push-button tail  

switch 4 times

SOS

Press the push-button tail  

switch 5 times

Memory function

Your 

Olympia AD220 Cree

®

 XP-G LED

 flashlight 

automatically memorizes the last light setting/

mode used when the flashlight next is turned 

on.  i.e., after being in any one of the five light 

settings (High

Middle

Low

Strobe

SOS) for 

3 seconds, the last one used will be memorized.

Maintenance and Precautions

1.  Do not disassemble the sealed head.  Doing 

so can cause damage to the flashlight and will 

void the warranty.  

2. Use high-quality batteries or you run the risk 

of the flashlight being damaged by electrolyte 

leakage or battery breakage.

3. If the flashlight will not be used for a long time, 

remove the batteries to avoid damage caused 

from battery leakage.

4. Lubricate the O-rings regularly using a 

Q-tip

®

.  Apply a small dab of silicone grease 

or petroleum jelly to the contacts to prevent 

corrosion.  Doing so will keep the flashlight 

properly sealed against water. If the O-rings are 

damaged after prolonged use, replace them.

5. Clean the flashlight contacts periodically 

especially if the light flickers or does not light 

up. There are different reasons for a flickering or 

non-working light:

A: The batteries may need to be replaced. 

Solution: Replace old/defective batteries with 

new ones (be sure to double check correct 

installation of + and - terminals).

B: The threads, PCB board contact or other 

contacts are dirty. 

Solution: Use a Q-tip

®

 to apply a tiny amount 

of alcohol to clean the contact points.

If the above methods do not work, please refer to 

the warranty policy listed in this user guide.

        Warning

The AD220 is a high-intensity lighting device and 

capable of causing eye damage. Please avoid 

shining the light directly into the eyes.

!

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Clip

Tail

Cap

Switch

Lanyard

Hole

Body

Head

Reviews: