Accessories for the SECURE Series
Motion Detector
(Art. No. 5993)
Read the operating manual thoroughly and observe the
information. Keep the operating manual close by for
future reference.
Important Information on the Motion Detector
■
The motion detector is designed for private use, indoors.
■
The motion detector only works in combination with an
alarm system from the SECURE series.
■
The motion detector must be installed within transmission
range of the base unit of the SECURE series alarm system.
Safety Instructions
The following safety information applies to the entire document.
Read and observe all the warning information to protect yourself
and the environment from any harm.
Warning
! This device can be used by child-
ren from the age of 8 and persons with
restricted physical, sensory or mental capa-
bilities or a lack of experience and knowl-
edge as long as they are supervised or have
been instructed with regard to safe use of
the device and are aware of the potential
risks involved with its use. Children must
never play with the device. Cleaning and
user maintenance may not be completed by
children without any supervision.
Warning
! NEVER complete any repairs to the
device yourself. Contact our Service depart-
ment. The device does not contain any parts
which the user needs to repair or service.
Warning
! Risk of suffocation! Children can
swallow small parts, packaging and protec-
tive foils. Keep the device and packaging out
of reach of children.
Attention
! Risk of property damage through
the use of inappropriate batteries! The use
of inappropriate batteries can cause a loss of
function of the device. Only use batteries of
the type described in Section Technical Data.
Attention
! Risk of property damage through
environmental influences! Prevent environ
-
mental influences such as exposure to
smoke, dust, vibration, chemicals, moisture,
heat and direct sunlight.
Important
! Before starting to position the sen-
sors, take into account that walls, ceilings and
sources of electrical disturbance can impair wire-
less communication.
Intended Use
The motion detector reacts to movements within the detection
range of the sensor.
A condition for complying with the intended use is that the equip-
ment is installed correctly and the information in the manual is
observed and maintained. Any other use is considered unintend-
ed use.
Scope of Delivery
Please check the contents of the package carefully. If anything is
missing or has been damaged during transport, DO NOT put the
motion detector into operation!
Motion detector
1
Batteries
1 x 9 V power pack
Assembly material
Mounting bracket, screws,
dowels
Operating manual
1
General View
The illustration at the beginning depicts the motion detector in
detail.
1
Motion sensor
2
LED
3
Battery compartment (on the rear)
Inserting the Batteries
1
Open the battery compartment by pressing the locking latch
on the top of the motion detector down using an appropri-
ate, pointed object.
2
Connect the 9 Volt battery to the battery clip, which is pro-
tected against reverse poling, and place the 9 Volt battery in
the battery compartment.
3
Close the battery compartment. The lock engages audibly.
Registering a Sensor
You must register the motion detector on the base unit. When
the motion detector detects a movement and triggers, it sends a
signal to the base unit and the base unit alarm sounds.
1
Press and hold the corresponding button on the base unit to
register sensors.
2
If necessary, disconnect the 9 V battery from the reverse
poling protected battery clip.
3
Connect the 9 Volt battery to the battery clip, which is pro-
tected against reverse poling, and place the 9 Volt battery in
the battery compartment.
4
Trigger the motion detector.
Installation
Positioning
Stand or hang the motion detector in a suitable position to moni-
tor the required area.
The motion detector detects movements within the scanning
area of up to 12 m with an angle of vision of 110°. The optimum
installation height is about 2 - 3 m above the ground.
Hanging on a Wall
You can also hang the motion detector on a wall. Use the assem-
bly material supplied to do this.
1
Use the holes in the mounting bracket as a drilling template
and drill two sufficiently large holes in the wall.
2
Assemble the mounting bracket using the dowels and screws
supplied.
3
Install the ball joint in the mounting bracket. The ball joint
snaps audibly into place.
4
Assemble the motion detector on the bracket for the ball
joint with the aid of the recess on the rear of the bracket .
5
Align the motion detector as necessary using the ball joint.
Setting Up the Motion Detector
Various settings can be defined using the jumpers on the PCB of
the motion detector.
It is preferable to define any settings before assembling the mo
-
tion detector at the installation location.
1
3
2
5
4
1
Sensitivity (
H
= High, L = Low)
2
Low battery power signal (
ON
, OFF)
3
Scanning interval (
5s
= 5 seconds pause between motion de-
tection, 5 Min. = 5 minutes pause between motion detection)
4
LED on/off (
ON
= LED on, OFF = LED off)
Settings which appear in bold print are the standard settings.
Important
! Risk of property damage through electrostatic dis-
charge. Use insulated tools when adjusting the jumpers on the
motion detector's PCB. Do not make contact with the jumpers or
PCB with bare hands.
Technical Data
Weight
Approx. 113 g
Dimensions (W x H x D)
57 x 110 x 44.5 mm
Radio frequency
868.5 MHz
Transmission power (max.):
1.57 mW
Batteries
1 x 9 V power pack
Permissible
ambient conditions
-10 °C to +40 °C at
30% to 75% rel. humidity
Information on Disposal
The adjacent symbol indicates that electrical and
electronic apparatus and batteries no longer required
must be disposed of separate from domestic waste in
accordance with legal directives.
You are legally obliged to dispose of batteries and bat-
tery packs at shops which sell batteries or collection points which
provide the corresponding containers. Disposal is free of charge.
The symbols indicate that the batteries must not be disposed
of in normal domestic waste and that they must be brought to
collection points provided by local public waste authorities.
Packaging materials must be disposed of according to
local regulations.
Guarantee
Dear Customer,
we are pleased that you have chosen this equipment.
In the case of a defect, please return the device together with the
receipt and original packing material to the point-of-sale.
Cleaning and Service
1
Clean the surface of the housing with a soft, lint-free cloth.
Never use any chemicals or scouring agents.
2
Check the functionality of each sensor registered once a
month and after changing the batteries.
3
Change the batteries at least once a year or after receiving
the relevant message from the alarm system.
Information on Conformity
Olympia Business Systems Vertriebs GmbH, Zum
Kraftwerk 1, 45527 Hattingen hereby declares that this
device fulfils the basic requirements and other
relevant provisions stipulated in the Directive 2014/53/
EC. The CE mark on the device confirms its conformity.
More detailed information on the Declaration of
Conformity is provided at
http://productip.
com/?f=6f1e9
or scan this QR code.
1
3
2
20171211_secure_zubehoer_bewegungsmelder.indd 2
02.07.2018 15:02:59
