Page 1 from 5
SOUNDER WITH BEACON FOR FIRE DETECTION PANEL
GENERAL
This device is Visual Alarm Devices (VAD)
for fire detection panels that offer a strong
sound output and an optical warning with a
beacon. The strong sound and the optical
warning beacon cover many square metres.
It features two inputs (N1, N2) for the
production of two different sounds.
This
device can co-operate with any fire detection
panel (BSR-2104, BSR-2114, BS-1632, BS-
1634, BS-1636, BS-636).
Installation and Connection
1.
First, remove the retaining screw, place a
flat blade screwdriver in the holes of the
plastic hooks and remove the plastic cover
(Image 1 on page 2).
2.
Remove carefully the beacon connector
(Image 2 on page 2).
3.
Use the supplied mounting parts to install
the siren’s base at a height of 2.4 metres
from the floor (figure 1 on page 2). Place the
plastic plugs and fasten the screws to the
mounting holes
.
Attention!! Make sure that the
siren’s base is installed upwards
as shown in
figure on page 4.
4.
Place the caps and make a hole in the
center using a small screwdriver.
Pass
through the caps the cables to connect the
device.
5.
The (
+N1
or the
+N2
)
terminal block
is
connected to the
(
+
)
output of
Alarm-1
or
Alarm-2
of the panel and the (
-
)
of the
terminal block is connected to the
(
-
)
out
put of
Alarm-1
or
Alarm-2
of the panel. Accordingly
connect in parallel all the sirens. (The
maximum number of sirens depends on the
type of the panel).
6
.
To select various
sound effects
use the
dipswitch 1,
2
and
3 and
choose the diserable
sound effect,
according to
tables 2 and 3 on
page 3.
7
.
For
LED effect
variation use the dipswitch
4 (Table 1) on page 2. On the last siren of the
line, we must connect in parallel with its power
cables, the terminal resistor that was removed
from the alarm contacts of the panel.
8.
Reinstall the beacon connector (step 2).
Refit the plastic cover until the plastic hooks
are securely attached (step 1) and fasten the
retaining screw (torque 0.6Nm). Attention!!
Make sure that the siren’s cover is installed in
the correct orientation.
9.
Test the device after installation.
Β
S-531
/1
ΤΕCHNICAL CHARACTERISTICS
OPERATION VOLTAGE
MAXIMUM CONSUMPTION
MAXIMUM SOUND OUTPUT in
1
m
Τ
YPE OF APPLICATION ENVIRONMENT
MOUNTING
COVERAGE (y)
BEACON
21-28V DC
Τ
ype
Α
1 Power
LED
Wall
6 m around the siren at an angle of 180°
94dB (sound effect 1
)
1.2W
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
TYPICAL WEIGHT
GUARANTEE
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
IP42C
COVERAGE VOLUME
FLASH RATE
FLASH COLOUR
86.4m³ (max)
1 Hz (Switchable to 0.5 Hz)
Red
EN 54-3:
2001 +Α1:2002 +Α2:2006
, EN 54-23: 2010
o
0 to 60 C
Up to 95%
2 years
230gr.
141 x 141 x 100 mm
CONSTRUCTION MATERIAL
Bayblend FR3010
,
transparent
polycarbonate
MOUNTING HEIGHT (x)
2.4m max
COVERAGE VOLUME CODE
W-2.4-6
921531007_09_0
0
8
Thank you for your trust in our products
Olympia Electronics - European manufacturer
