ΣΕΙΡΗΝΑ ΓΙΑ ΠΙΝΑΚΑ ΠΥΡΑΝΙΧΝΕΥΣΗΣ
ME
ΦΑΡΟ
@Olympiaelectro
Olympia Electronics O
lympiaElectronics
Olympia Electronics
Πιστεύουμε στην
Παράγουμε στην
Β
S-531
ΤΕ
CHNICAL CHARACTERISTICS
220 - 240V AC/50-60Hz
3
VA
3
0 mAAC
4mA AC
1
power LED
94dB (sound effect 1
)
AUTONOMOUS SIREN
WITH BEACON
Β
S-521
/1
GENERAL
This device is Visual Alarm Devices (VAD) for
fire detection panels that offer a strong sound
output and an optical warning with a
beacon. The strong sound and the optical
warning beacon cover many square metres.
Installation and Connection
1.
First, remove the retaining screw, place a flat
blade screwdriver in the holes of the plastic
hooks and remove the plastic cover (Image 1
on page 2).
2.
Remove carefully the beacon connector
(Image 2 on page 2).
3.
Use the supplied mounting parts to install
the siren’s base at a height of 2.4 metres
from the floor (
figure
2 on page 3). Place the
plastic plugs and fasten the screws to the
mounting holes
.
Attention!! Make sure that the
siren’s base is installed upwards
as shown in
figure on page 4.
4.
Place the caps and make a hole in the
center using a small screwdriver.
Pass through
the caps the cables to connect the device.
5.
Connect the alarm buttons with two cables
(as in Figure 1 if more than one) to the
terminal block BUTTON. Then power the siren
with 230V AC.
6.
C
onnect the battery connector (
Image
3 on
page 2) and is ready to operate.
7.
To select various
sound effects
use the
dipswitch 1,
2
and
3 and
choose the diserable
sound effect,
according to
table 2 on page 3.
8.
For
LED effect
variation use the
dipswitch 4 (table 1 on page 3).
9. Reinstall the beacon connector (step
2).
Refit the plastic cover until the plastic
hooks are securely attached (step 1) and
fasten the retaining screw (torque 0.6Nm).
Attention!! Make sure that the siren’s cover
is installed
in the correct orientation
.
10.
Test the device after installation.
3
.
6
V 1.5Ah NiMH
90
minutes
360mA DC
24 Hours
BATTERY TYPE
RECHARGE TIME
MAXIMUM BATTERY CURRENT CONSUMPTION
MINIMUM DURATION
MAXIMUM SOUND OUTPUT in
1
m
Τ
YPE OF APPLICATION ENVIRONMENT
MOUNTING
COVERAGE (y)
BEACON
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
TYPICAL WEIGHT
GUARANTEE
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
COVERAGE VOLUME
FLASH RATE
FLASH COLOUR
CONSTRUCTION MATERIAL
MOUNTING HEIGHT (x)
COVERAGE VOLUME CODE
OPERATION VOLTAGE
MAXIMUM AC POWER CONSUMPTION
MAXIMUM AC CURRENT CONSUMPTION
STANDBY AC CURRENT CONSUMPTION
Τ
ype
Α
Wall
6 m around the siren at an angle of 180°
IP42C
86.4m³ (max)
1 Hz (Switchable to 0.5 Hz)
Red
EN 54-3, EN 54-23
o
5 to 40 C
Up to 95%
2 years
400gr.
141 x 141 x 100 mm
Bayblend FR3010
,
transparent
polycarbonate
2.4m max
W-2.4-6
92152100
6
_09_0
0
4
Page
1
from 4
Thank you for your trust in our products.
Olympia Electronics - European manufacturer
.
92152100
6
_09_0
0
4
Page 4 from 4
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing.
Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72
nd
km
.
O
.
N
.
R
.
Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
