OLT SpaceMaker Manual Download Page 1 | Manualshive

Page: 1 / 45

OLT SpaceMaker Manual Download Page 1

8x12 SpaceMaker - Bevel
with Metal Roof Assembly

Manual

Version #2.0

May 26, 2020

1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 1

In the event of a missing or broken piece, call the Outdoor Living Today Customer Support Line @ 1-888-658-1658 with-
in 30 days of the delivery of your purchase. It is our commitment to you to courier replacement parts, free of charge,
within 10 business days of this notification. Replacement parts will not be provided free of charge after the 30 day
grace period.

All structures purchased from Outdoor Living Today are covered for a period of one year for defects in manufacturing
and workmanship. Costs incurred for customer installations are not included.

Failure to use supplied parts included in this kit could result in poor product performance and may void your warranty.
Please contact Outdoor Living Today’s Customer Toll Free Line if you plan to deviate from our written instructions.

- Snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it
is advisable to sweep snow off roof frequently.
- If the product is elevated, any structural and building code requirements are solely
the customer's responsibility, and should be abided by.
- In areas with high or gusty wind conditions, it is advisable to install the structure
securely to the ground.
- Have a regular maintenance plan to ensure screws, doors, windows and parts are
tightly affixed.

Customer agrees to hold Outdoor Living Today and any Authorized
Dealers free of any liability for improper installation, maintenance and
repair.

Safety Points and Other Considerations
Our products are built for use based on
proper installation on level ground and
normal residential use. Please follow the
instruction manual when building your
shed and retain the manual for future
maintenance purposes.

Customers are responsible for ensuring
a solid, level, well-draining site for
construction.

Please check with your local municipal
or county by-laws before ordering this
product to confirm it complies with
building codes.

Thank you for purchasing a
8x12 SpaceMaker. Please take
the time to identify all the parts
prior to assembly.

Stock Code #
SM812-Metal

1
2
3
...
»

Summary of Contents for SpaceMaker














































Reviews:

No comments