manualshive.com logo in svg

Olivetti DP-670, Service Manual, Page: 89 / 103

Share
Download
Olivetti DP-670 Service Manual Download Page 89

3K5

2-1-3

(1) Operation of original switchback

In the double-sided original mode, after the first side of an original is scanned, the switchback feedshift guide is activated
to switch the conveying path to the switchback tray side and the original is fed to the switchback tray. Then, the original is
reversed by the reverse rotation of the original switchback motor (OSBM) and conveyed again to the original conveying
section. After the second side is scanned, the original is fed temporarily to the switchback tray, is reversed, is conveyed
without scanning, and then is ejected to the exit tray. Also the switchback press solenoid (SBPSOL) is activated to
release the switchback pulley for preventing original jams in the original switchback section.

Figure 2-1-3

First side scanning       Switchback tray

Original conveying motor (OCM): Forwerd rotation

Original switchback motor (OSBM): Forwerd rotation

Switchback feedshift solenoid (SBFSSOL): ON

Original switchback operate

Original conveying motor (OCM): Stop

Original switchback motor (OSBM): Reverse rotation

Switchback feedshift solenoid (SBFSSOL): OFF

Second side scanning       Switchback tray

Original conveying motor (OCM): Forwerd rotation

Original switchback motor (OSBM): Forwerd rotation

Switchback feedshift solenoid (SBFSSOL): ON

Original switchback operate

Original conveying motor (OCM): Stop

Original switchback motor (OSBM): Reverse rotation

Switchback feedshift solenoid (SBFSSOL): OFF

Conveyed without scanning       Eject tray

Original conveying motor (OCM): Forwerd rotation

Original switchback motor (OSBM): Forwerd rotation

Switchback feedshift solenoid (SBFSSOL): OFF

Y108671-9 Service Manual 

Summary of Contents for DP-670








































































































Reviews:

No comments