manualshive.com logo in svg

Olivetti DP-670, Service Manual, Page: 83 / 103

Share
Download
Olivetti DP-670 Service Manual Download Page 83

3K5-2

1-6-1

1-6 Requirements on PWB Replacement

1-6-1  Upgrading the firmware (DP-670/models with color touch panel)

Follow the procedure below to upgrade the firmware.

Firmware upgrading requires the following tools:

Compact Flash (Products manufactured by SANDISK are recommended.) or USB memory

NOTE

When writing data to a new Compact Flash from a computer, be sure to format it in advance.

Procedure

1. Press the power key on the operation panel 

to off. Make sure that the power indicator 
and the memory indicator are off before 
turning off the main power switch. And then 
unplug the power cable from the wall outlet.

2. Insert Compact Flash or USB memory in a 

notch hole of the machine.
Insert the surface of Compact Flash toward 
the machine rear.

3. Insert the power plug and turn the main 

power switch on. Upgrading firmware starts 
for 3 minutes.

Caution:

Never turn the main power switch off during 
upgrading.

Figure 1-6-1

4. [Completed] is displayed on the touch panel 

when upgrading is complete.

5. Press the power key on the operation panel 

to off. Make sure that the power indicator 
and the memory indicator are off before 
turning off the main power switch. And then 
unplug the power cable from the wall outlet.

6. Remove Compact Flash or USB memory 

from the machine.

7. Insert the power plug and turn the main 

power switch on.

USB memory

Compact Flash

Y108671-9 Service Manual 

Summary of Contents for DP-670








































































































Reviews:

No comments