manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-3-55

Description

Sets the DP image scanning density

Purpose

Changes the setting if the background image appears when scanning bluish original or originals with 
slightly thick background Adjusts the  image difference between the table scanning and DP scanning CIS 
scanning is not corrected.

Setting

1.Press the [Start] key.
2.Select the item to set.
3.By using the [+] [-] keys or the numeric keys, change the setting value.

4.Press the [Start] key to set the setting value.

Completion

Press the [Stop] key.

*: The screen for selecting a maintenance item No. is displayed.

U074

Adjusting the DP input characteristics
(Message: Adjust DP Input)

Items

Contents

Setting range

Initial

setting

Coefficient

DP image scanning density correction

0: No correction
1: Low-level 
2: Middle-level 
3: High-level

1

DP Color 
Regist

Permitting the color registration correction opera-
tion

1: On
2: Off

1

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

Oce sx1481 User Manual preview
sx1481
Brand: Oce Pages: 192
Oce OP20 Operation Manual preview
OP20
Brand: Oce Pages: 22
Oce FX3000 SERIES Quick Setup Manual preview
FX3000 SERIES
Brand: Oce Pages: 41
Oce fx2081 Installation Manual preview
fx2081
Brand: Oce Pages: 28
Oce im5530 Specifications preview
im5530
Brand: Oce Pages: 6
QMS 2560 Options Installation preview
2560
Brand: QMS Pages: 104
Oce im2330 Printing Manual preview
im2330
Brand: Oce Pages: 386
Oce im2330 Specifications preview
im2330
Brand: Oce Pages: 2
Oce cm2520 Safety Information & Getting Started preview
cm2520
Brand: Oce Pages: 27
Oce im2330 Operator'S Manual preview
im2330
Brand: Oce Pages: 324
Oki C7550 Reference Manual preview
C7550
Brand: Oki Pages: 45
SII DPU-30 Technical Reference preview
DPU-30
Brand: SII Pages: 85
Lexmark C6160 User Manual preview
C6160
Brand: Lexmark Pages: 142
Pantum P3020 Series User Manual preview
P3020 Series
Brand: Pantum Pages: 95
Canon MultiPASS C530 Quick Start Manual preview
MultiPASS C530
Brand: Canon Pages: 8
Canon MultiPASS F30 Reference Manual preview
MultiPASS F30
Brand: Canon Pages: 58
Canon MultiPASS F20 Basic Manual preview
MultiPASS F20
Brand: Canon Pages: 110
Canon MultiPASS MP360 User Manual preview
MultiPASS MP360
Brand: Canon Pages: 162

Brands by name

Popular brands

Load more brands