Olivetti d-Color MF220 Copy Operations Download Page 210

Page: 210 / 315

Paper

8-4

d-Color MF360/280/220 (Version 3)

8.1

8.1.2

Loading paper

This section describes how to load paper into each tray.

If printing stops due to the tray being empty, load paper into the tray. Printing restarts automatically.

For the types of paper to be used, refer to page 12-3.

Loading paper in Tray 1, Tray 2, Tray 3, or Tray 4

The procedure for loading paper is common between

Tray 1

Tray 2

Tray 3

, and

Tray 4

The following procedure describes how to load paper into

Tray 1

Tray 3

and

Tray 4

are optional.

When [Auto Detect] is selected on the [Paper] tab, the size of loaded paper is automatically detected.

Pull out

Tray 1

1. Film

NOTICE

Be careful not to touch the

Film

Slide the

Lateral Guide

to fit the size of paper being loaded.

If the

Lateral Guide

are not positioned correctly for the loaded

paper, the paper size will not be correctly detected.

Load the paper into the tray so that the side of the paper to be
printed on (the side facing up when the package was unwrapped)
faces up.

Do not load so many sheets of paper that the top of the stack
is higher than the

mark.

If paper is curled, flatten it before loading it.

If special paper is loaded, the paper type must be specified.

Load letterhead paper so that the side to be printed on faces
down.

Tray 1

Reference

To configure paper settings:

Press [Basic]

[Paper].

Summary of Contents for d-Color MF220




























































































































































































































































































































Search results

Summary of Contents for d-Color MF220

Reviews:

Related manuals for d-Color MF220

Brands by name

Popular brands

Olivetti d-Color MF220, Copy Operations

Search results

Summary of Contents for d-Color MF220

Reviews:

Related manuals for d-Color MF220

Brands by name

Popular brands