Olivetti d-Color MF2001 Service Manual Download Page 91

Page: 91 / 333

2KZ/2K0

1-3-53

U140

Setting developer bias

Description

Setting the value of various developer bias.

Purpose

To check and setting the value of developer bias.

Method

1. Press the start key.

2. Select the item to be set or displayed.

Setting: [Mag DC/Sleeve DC/Clock Freq/Clock Duty/AC Ctrl]

1. Select the item to be set.

2. Change the setting value using the cursor left/right keys or numeric keys.

3. Press the start key. The value is set.

Item No.

Description

Display

Description

Mag DC

Setting the value of magnet DC bias.

Sleeve DC

Setting the value of sleeve DC bias.

Clock Freq

Setting the value of clock frequency.

Clock Duty

Setting the value of clock duty.

AC Ctrl

Setting the value of AC control voltage.

On Timing

Setting the value of developer On timing.

Off Timing

Setting the value of developer Off timing.

Display

Description

Initial

setting

1st

Setting the value of yellow.

450/150/36/27/1400

2nd

Setting the value of cyan.

480/180/36/27/1400

3rd

Setting the value of magenta.

480/180/36/27/1400

4th

Setting the value of black.

450/150/36/27/1400

Remove 1st

Setting the value of remove yellow.

50/150/36/27/1000

Remove 2nd

Setting the value of remove cyan.

50/150/36/27/1000

Remove 3rd

Setting the value of remove magenta.

50/150/36/27/1000

Remove 4th

Setting the value of remove black.

50/150/36/27/1000

Remove 1st Half Setting the value of remove yellow Half.

350/180/36/27/1200

Remove 2nd Half Setting the value of remove cyan Half.

350/180/36/27/1200

Remove 3rd Half Setting the value of remove magenta Half.

350/180/36/27/1200

Remove 4th Half Setting the value of remove black Half.

350/180/36/27/1200

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 91 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: