Olivetti d-Color MF2001 Service Manual Download Page 89

Page: 89 / 333

2KZ/2K0

1-3-51

U127

Checking/clearing the transfer count

Description

Displays and clears the counts of the transfer counter.

Purpose

To check the count after replacement of the

transfer belt unit or

transfer roller. Also to clear the

counts after replacing transfer roller.

Method

1. Press the start key. The current counts of the transfer counter is displayed.

Clearing

1. Select [Clear].

2. Press the start key. The counter value is cleared.

Setting

1. Change the counter value using the cursor left/right keys or numeric keys.

2. Press the start key. The counter value is set.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U135

Checking toner motor operation

Description

Drives toner motors.

Purpose

To check the operation of toner motors.

Remarks

When driving the toner motors long time or several times, developing section becomes the toner

full and is locked.

Method

1. Press the start key.

2. Select [Toner].

3. Press the start key. The operation starts.

Completion

Press the stop key after operation stops. The screen for selecting a maintenance item No. is dis-

played.

Item No.

Description

Display

Description

Mid Trans

Transfer belt unit counter value

2nd Trans

Transfer roller counter value

Cnt

Transfer counter value

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 89 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: