Olivetti d-Color MF2001 Service Manual Download Page 80

Page: 80 / 333

2KZ/2K0

1-3-42

U100

Setting the main high voltage

Description

Performs main charging.

Purpose

To check main charging.

Setting: [IDC Bias]

1. Select an item to be set.

2. Change the setting value using the cursor left/right keys or numeric keys.l

3. Press the start key. The value is set.

Completion

Press the stop key when main charger output stops. The screen for selecting a maintenance item

No. is displayed.

Item No.

Description

Display

Description

Setting

range

Initial

setting

1st

Set value of the MC DC bias (Yellow)

0 to 250

145

2nd

Set value of the MC DC bias (Cyan)

0 to 250

145

3rd

Set value of the MC DC bias (Magenta)

0 to 250

145

4th

Set value of the MC DC bias (Black)

0 to 250

145

Service Manual Y113010-4

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 80 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: