Olivetti d-Color MF2001 Service Manual Download Page 75

Page: 75 / 333

2KZ/2K0

1-3-37

U071

Adjustment: Trailing edge registration

1. Change the setting value using the cursor left/right keys or numeric keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-13

2. Press the start key. The value is set.

Caution

If the first side is adjusted, check the second side and if adjustment is required, carry out the

adjustment.

Check the copy image after the adjustment. If the image is still incorrect, perform the following

adjustments in maintenance mode.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Original

Copy

example 1

Copy

example 2

U071

U404

( P.1-3-74)

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 75 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: