Olivetti d-Color MF2001 Service Manual Download Page 64

Page: 64 / 333

2KZ/2K0

1-3-26

U053

Setting the adjustment of the motor speed

Description

Performs fine adjustment of the speeds of the motors.

Purpose

To adjust the speed of the respective motors when the magnification is not correct.

Method

1. Press the start key.

2. Select the item to be adjusted.

Item No.

Description

Display

Description

Setting

range

Initial

setting

Feed

Conveying motor (CM) speed adjust-

ment

-50 to 50

Exit

Eject motor (EM) speed adjustment

-40 to 40

Drum(CMY)

Drum motor (DRM-YCM) speed adjust-

ment

-50 to 50

Drum(K)

Drum motor (DRM-K) speed adjust-

ment

-50 to 50

DLP(CMY)

DLP motor (DEVM-YCM) speed adjust-

ment

-50 to 50

DLP(K)

DLP motor (DEVM-K) speed adjust-

ment

-50 to 50

Fixing

Fixing motor(FUM) speed adjustment

-50 to 50

Porygon(CMY)

Porygon motor(PM-YCM) speed

adjustment

-20 to 20

Porygon(K)

Porygon motor (PM-K) speed adjust-

ment

-20 to 20

Service Manual Y113010-4

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 64 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: