Olivetti d-Color MF2001 Service Manual Download Page 61

Page: 61 / 333

2KZ/2K0

1-3-23

U034

5. Change the setting value using the cursor left/right keys or numeric keys.

For output example 1, increase the value. For output example 2, decrease the value.

Figure 1-3-3

6. Press the start key. The value is set.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the following

adjustments in maintenance mode.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Center line of printing
(within ± 0.5 mm)

Correct image

Output

example 1

Output

example 2

U034

U067

( P.1-3-32)

U072

( P.1-3-38)

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 61 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: