Olivetti d-Color MF2001 Service Manual Download Page 57

Page: 57 / 333

2KZ/2K0

1-3-19

U031

Checking switches and sensors for paper conveying

Description

Displays the on-off status of each paper detection switch or sensor on the paper path.

Purpose

To check if the switches and sensors for paper conveying operate correctly.

Method

1. Press the start key.

2. Turn each switch or sensor on and off manually to check the status.

When a switch or sensor is detected to be in the ON position, the display for that switch or

sensor will be “1”.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Display

Switches and sensors

Switch 00000000

1st digit

Euser pre sensor (FUPS)

2nd digit

Bridge detection switch (BRDSW)

3rd digit

Job paper full sensor (JPFS)

4th digit

Paper full sensor (PFS)

5th digit

Feed sensor (FS)

6th digit

Duplex sensor (DUS)

7th digit

Eject sensor (ES)

8th digit

Registration sensor (RS)

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 57 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: