Olivetti d-Color MF2001 Service Manual Download Page 39

Page: 39 / 333

2KZ/2K0

1-3-1

1-3 Maintenance Mode

1-3-1 Maintenance mode

The machine is equipped with a maintenance function which can be used to maintain and service the

machine.

(1) Executing a maintenance item

Enter “10871087” using

the numeric keys.

Enter the maintenance item

number using the cursor left/right keys

or numeric keys.

The selected maintenance item is run.

Press the stop key.

Press the start key.

Start

End

Maintenance mode is entered.

The maintenance item is selected.

Maintenance mode is exited and
the system is restarted to initialize it
and to reflect the setting.

Repeat the same

maintenance item?

Run another maintenance

item?

Turn the main power switch off and on.

Yes

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 39 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: