Olivetti d-Color MF2001 Service Manual Download Page 250

Page: 250 / 333

2KZ/2K0

2-1-5

2-1-2 Drum section

The drum section consists of the drum, the charger roller unit, and the cleaning unit, and the drum surface is

uniformly charged in preparation for formation of residual image by laser beam.

After transfer is complete, toner remaining on the drum surface is chipped off with the cleaning blade and is

collected to the waste toner box with the sweep roller. The cleaning lamp (CL) consists of LEDs and removes

residual charge on the drum before main charging.

Figure 2-1-7 Drum section

1. Drum

2. Charger roller

3. Charger cleaning roller

4. Charger case

5. Cleaning blade

6. Sweep roller

7. Drum frame

8. Cleaning lamp (CL)

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 250 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: