Olivetti d-Color MF2001 Service Manual Download Page 235

Page: 235 / 333

2KZ/2K0

1-5-31

(2) Detaching and refitting the engine PWB

Procedure

1. Remove the rear cover.

(See page 1-5-5)

2. Remove the main PWB.

(See page 1-5-5)

3. Remove fourteen screws and then

remove the mount board for main PWB.

Figure 1-5-57

4. Remove all conectors from the engine

PWB.

5. Remove four screws and then remove

the engin PWB.

6. Check or replace the engine PWB and

refit all the removed parts.

CAUTION:

When replacing the engine

PWB, remove the EEPROM (U15) from

the engine PWB that has been removed

and then reattach it to the new engine

PWB.

Figure 1-5-58

Screws

Screw

Screws

mount bord for mein PWB

Screws

Screw

Engine PWB

Engine PWB connectors

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 235 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: