Olivetti d-Color MF2001 Service Manual Download Page 223

Page: 223 / 333

2KZ/2K0

1-5-19

1-5-8 Drive section

(1) Detaching and refitting the conveying motor

Procedure

1. Remove the rear cover.

(See page 1-5-5)

2. Remove the connector from the

conveying motor PWB.

3. Remove three screws and then remove

the conveying motor.

4. Check or replace the conveying motor

and refit all the removed parts.

Figure 1-5-33

(2) Detaching and refitting the drive unit

Procedure

1. Remove the rear cover.

(See page 1-5-5)

2. Remove three connectors and then

release the waires from the hooks.

3. Remove four screws and then remove

the drive unit.

4. Check or replace the drive unit and refit

all the removed parts.

Figure 1-5-34

Screw

Conveying motor

Connector

Conveying
motor PWB

Screw

Drive unit

Screw

Wires

Connectors A

Hooks

Drive unit

Connector B

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 223 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: