Olivetti d-Color MF2001 Service Manual Download Page 217

Page: 217 / 333

2KZ/2K0

1-5-13

(4) Detaching and refitting the registration cleaner

Procedure

1. Open the front cover. (See page 1-5-3)

2. Open the duct cover. (See page 1-5-15)

3. Set the cleaner lever (yellow) up and

draw the registration cleaner frontward.

4. Check or replace the registration

cleaner and refit all the removed parts.

Figure 1-5-21

(5) Detaching and refitting the MP tray

Procedure

1. Open the MP tray.

2. Release two fulcrums of the MP tray by

using a flat screwdriver.

3. Pull two straps upwards to remove.

4. Remove the MP tray.

Figure 1-5-22

Registration cleaner

Cleaner lever
(yellow)

Flat screwdriver

Flucrum

MP tray

Straps

Flucrum

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 217 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: