Olivetti d-Color MF2001 Service Manual Download Page 212

Page: 212 / 333

2KZ/2K0

1-5-8

(4) Detaching and refitting the eject rear cover

Procedure

1. Release two hooks by using a flat

screwdriver and then remove the tray

left cover.

Figure 1-5-12

2. Pull the left upper cover downwards

and then release two hooks A.

3. Pull the left upper cover upwards and

then release three hooks B.

4. Remove the left upper cover.

ATTENTION:

At the time of replace the

left upper cover, confirm the position of

the scaner lock lever .

Figure 1-5-13

Tray left cover

Hooks

Flat screwdriver

Left upper cover

Hooks B

Hooks A

Service Manual Y113010-4

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 212 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: