Olivetti d-Color MF2001 Service Manual Download Page 187

Page: 187 / 333

2KZ/2K0

1-4-41

(1) No image appears (entirely white).

(2) No image appears (entirely black).

Print example

Causes

Check procedures/corrective measures

Defective

transfer

bias output.

Defective connector cable

or poor contact in the con-

nector.

Reinsert the connector. Also check for conti-

nuity of the connector cable. If necessary,

replace the cable.

High voltage PWB and engine PWB (YC15)

High voltage PWB sub and engine PWB

(YC13)

Defective high voltage

PWB.

Replace the high voltage PWB.

Defective high voltage PWB

sub.

Replace the high voltage PWB sub.

Defective engine PWB.

Replace the engine PWB (see page 1-5-31).

Defective

developer

bias output.

Defective connector cable

or poor contact in the con-

nector.

Reinsert the connector. Also check for conti-

nuity of the connector cable. If necessary,

replace the cable.

High voltage PWB and engine PWB (YC15)

Defective high voltage

PWB.

Replace the high voltage PWB.

Defective engine PWB.

Replace the engine PWB (see page 1-5-31).

No LSU

laser is out-

put.

Defective laser scanner

unit.

Replace the laser scanner unit

(see page 1-5-20).

Defective main PWB.

Replace the main PWB (see page 1-5-30).

Print example

Causes

Check procedures/corrective measures

No main

charging.

Defective connector cable

or poor contact in the con-

nector.

Reinsert the connector. Also check for conti-

nuity within the connector cable. If none,

replace the cable.

High voltage PWB and engine PWB (YC15)

Defective charger roller unit. Replace the charger roller unit

(see page 1-5-16).

Defective high voltage

PWB.

Replace the high voltage PWB.

Defective engine PWB.

Replace the engine PWB (see page 1-5-31).

Exposure

lamp fails to

light.

Defective connector cable

or poor contact in the con-

nector.

Reinsert the connector. Also check for conti-

nuity within the connector cable. If none,

replace the cable.

LED PWB and main PWB (YC112)

CCD PWB and main PWB (YC113)

Defective CCD PWB.

Replace the image scanner unit

(see page 1-5-21).

Defective main PWB.

Replace the main PWB (see page 1-5-30).

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 187 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: