Olivetti d-Color MF2001 Service Manual Download Page 154

Page: 154 / 333

2KZ/2K0

1-4-8

7963

Sequence error 6

The finisher does not deliver the eject-complete

command in 15 seconds after the bridge eject

sensor is turned off.

9001

DP original conveying jam

DP timing sensor (DPTS) turns off within the speci-

fied time since the sensor turns on.

9004

DP original switchback jam

During duplex switchback scanning, the DP regis-

tration sensor (DPRS) does not turn on within

specified time of the DP timing sensor (DPTS)

turning off.

9010

DP open

The DP is opened during original feeding.

Sensor in the conveying system is on when the

power is turned on or the cover is closed.

9011

DP top cover open

The DP top cover is opened during original feed-

ing.

9110

DP paper feed sensor stay

jam

The DP paper feed sensor (DPPFS) or DP regis-

tration sensor (DPRS) does not turn off within the

specified time of the DP timing sensor (DPTS)

turning on.

9200

DP registration sensor non

arrival jam

The DP registration sensor (DPRS) does not turn

on within the specified time of the DP paper feed

sensor (DPPFS) turning on.

9400

DP timing sensor non arrival

jam

The DP timing sensor (DPTS) does not turn on

within the specified time of the DP registration sen-

sor (DPRS) turning on (Retry 5 times).

9410

DP timing sensor stay jam

The DP timing sensor (DPTS) does not turned off

within the specified time its turning on.

Code

Contents

Conditions

Jam

location*

*: Refer to figure 1-4-1 for paper jam location (see page 1-4-1).

Service Manual Y113010-4

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 154 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: