Olivetti d-Color MF2001 Service Manual Download Page 153

Page: 153 / 333

2KZ/2K0

1-4-7

6023

Staple cover open

The staple cover is opened during operation.

6043

DF top cover open

The DF top cover is opened during operation.

6103

DF paper conveying sensor

non arrival jam

The paper conveying sensor (PCS) does not

turned on even if a specified time has elapsed after

the machine eject signal was received.

6113

DF paper conveying sensor

stay jam

The paper conveying sensor (PCS) does not turn

off within the specified time of its turning on.

6123

DF paper conveying sensor

remaining jam

The paper conveying sensor (PCS) does not

turned on when the power is turned on or the cover

is closed.

6413

DF eject paper sensor stay

jam

The eject paper sensor (EPS) does not turn off

within the specified time.

6423

DF eject paper sensor

remaining jam

The eject paper sensor (EPS) does not turned on

when the power is turned on or the cover is closed.

6803

Front adjustment plate oper-

ation ON error

The adjustment sensor 1 (ADS1) does turned on

when the job is executed.

6813

Front adjustment plate oper-

ation OFF error

The adjustment sensor 1 (ADS1) does not turned

off when the job is executed.

6903

Rear adjustment plate oper-

ation ON error

The adjustment sensor 2 (ADS2) does not turned

on when the job is executed.

6913

Rear adjustment plate oper-

ation OFF error

The adjustment sensor 2 (ADS2) does not turned

off when the job is executed.

7013

Staple operation error

The next staple hasn't head-poked for the next

copy to bind after a predetermined interval while

clinching has commenced.

7023

Staple initial operation error

Head-poking has not been accomplished after 10

attempts in the initialization at power up or closing

the cover.

7913

Sequence error 1

(operation prohibited)

Operation commenced in the state the finisher is

prohibited to operate.

7923

Sequence error 2

(initialoperation error)

A request for maintenance mode has occurred in

the state the finisher is prohibited to operate or has

commenced operation.

7933

Sequence error 3

(Error in the reception of

backup data)

A backup data command has been received in the

state the operation has initiated.

7943

Sequence error 4

(standby)

Operation has started in the state standby is pro-

hibited.

7953

Sequence error 5

(Error in between copies)

An illegal inter-page or inter-copy interval has

occurred.

Code

Contents

Conditions

Jam

location*

*: Refer to figure 1-4-1 for paper jam location (see page 1-4-1).

Y113010-4

Sevice Manual

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 153 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: