Olivetti d-Color MF2001 Service Manual Download Page 144

Page: 144 / 333

2KZ/2K0

1-3-106

Center line
alighment

Alignment of the cassette and MP tray and duplex

Description

Perform settings for the center line adjustment.

Purpose

Perform if the alignment has not been obtained after the center line adjustment.

Method

1. Enter the service menu.

2. Select [Center Line Adjustment].

3. Press [Save].

Completion

Press the Save key in the setting display.

Developer

Perform the toner installation of the developer unit.

Description

Perform the toner installation when the developer unit has been replaced.

Purpose

Perform when the developer unit is replaced.

Method

1. Enter the service menu.

2. Select [Developer unit].

3. Press [Start] in the confirmation display.

Completion

The toner installation is performed when power is turned on and off.

Service items

Description

Service Manual Y113010-4

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 144 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: