Olivetti d-Color MF2001 Service Manual Download Page 142

Page: 142 / 333

2KZ/2K0

1-3-104

(2) Executing a service mode

(3) Description of service mode

Service items

Description

Enable
Repaired Unit

Release the disconnection of the cassette and the document feeder.

Description

Restore the system control when the defective unit is replaced to enable the unit.

The menu is displayed only when the unit is detached for failure.

Purpose

Perform when the defective unit is replaced.

Method

1. Enter the service menu.

2. Select [Enable Repaired Unit].

3. Press [Start].

Completion

The unit is automatically powered after execution.

Press the System Menu/Counter key.

Select [Adjust/Maint.]

using the cursor up/down keys.

The selected service mode is run.

Select [Service Setting]

using the cursor up/down keys.

Start

End

The Sys. Menu/Count. menu appears.

The Adjust/Maint. menu appears.

The Service Setting menu appears.

Service Manual Y113010-4

Summary of Contents for d-Color MF2001













































































































































































































































































































































Search results

Summary of Contents for d-Color MF2001

Reviews:

Olivetti d-Color MF2001, Service Manual, Page: 142 / 333

Search results

Summary of Contents for d-Color MF2001

Reviews: