manualshive.com logo in svg

Oki IP-5630, User Manual, Page: 189 / 265

Share
Download
Oki IP-5630 User Manual Download Page 189

189

Advanced operations

Controlling the media advance 

adjustment value

Change the media advance adjustment value during printing 

 

1

 

 

PRINTING...  
STANDARD ND BI

 

                 

  

, 

Press the 

Up

 or 

Down

 button while 

PRINTING...

 is displayed.

2

 

 

FINE ADJ VAL:099.80% 

2

099.80%

Adjustment 
value when 
printing starts

ncrease or decrease the value by 0.01% with the Up and 
Down buttons. 
(Setting range: 97.00% to 106.00%)

 

                 

  

, 

 Press the 

Up

 and 

Down

 buttons to modify 

the adjustment value. 

 
The changed value is applied immediately after change.  
The adjustment value displayed when the print started 
does not change until the print finishes.

3

 

 

FINE ADJ VAL:099.80% 

2

099.96%

 

                 

  three seconds

The changed value is registered as the adjustment value 
and will be applied for the next print.  
The panel display of the adjustment value during printing 
returns automatically to the previous screen if no buttons 
are pressed for three seconds. 

 

 

PRINTING...  
STANDARD ND BI

Be

fo

re

 p

rin

tin

g

Lo

adi
ng

 the

 m

edi

a

A

dj

us

tm

ent

M

ai

nt

enan
ce

A

dv

an

ce

d 

op

er

ati

on

s

Trou
ble

sh

oo

tin

g

M

enu

 tr

ee

Ap
pe

nd

ix

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments