manualshive.com logo in svg

Oki IP-5630, User Manual, Page: 180 / 265

Share
Download
Oki IP-5630 User Manual Download Page 180

180

Advanced operations

6

 

 

SET ORIGIN 
*OK?

 

                 

  Carriage stops moving.

7

 

 

SET ORIGIN 
OK? 

 

                 

  

Press the 

OK

 button to set the origin. 

The carriage returns, and the printer enters online state and 
becomes ready to print.

 

 

SETTING ORIGIN...  
PLEASE WAIT

 

                 

  

 

 

PRINTER READY 
01: PAPER / 1626mm 

During origin setting mode, a   symbol is displayed next to 
the media width value.

 
 

Exit origin setting mode 

To cancel an origin that has been set, reinstall the media, or exit the origin setting mode following the procedure 
below. 
 

1

 

 

PRINTER READY 
01: PAPER / 1626mm 

 

                 

  

Press the 

Left

 button when the printer is 

online in origin setting mode.

2

 

 

CANCEL ORIGIN 
OK? 

 

                 

  

Press the 

OK

 button to exit origin setting 

mode.

3

 

 

PRINTER READY 
01: PAPER / 1626mm

The   symbol disappears.

 
 

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments